I Feel - Mitsubishi Electric Mr.SLIM MSH24W Manual De Instrucciones

I FEEL... AUTO OPERATION
•
To start operation:
I
With the " (I FEEL...)" auto operation mode,
the optimum room condition can be set automati-
cally with a one-touch operation.
•
To stop operation:
I
˚C
CLOCK
•
AMPM
I
AMPM
TOO TOO
ON/OFF
WARM COOL
•
I
FAN STOP
I FEEL COOL
When "
the
VANE START
HEAT DRY
Each time the button is pressed, the operation mode is
changed in sequence:
MODE WIDE VANE HR.
→ → → → →
LONG MIN.
RESET CLOCK
ON/OFF
Press the button.
When the " (I FEEL...)" mode is selected, the air
conditioner is automatically controlled at the optimum
temperature.
ON/OFF
Press the button.
If you feel slightly warm:
TOO
WARM
Press the button to lower the tempera-
ture.
°
One press lowers the temperature by about 2 F.
If you feel slightly cool:
TOO
COOL
Press the button to raise the tempera-
ture.
°
One press raises the temperature by about 2 F.
(I FEEL...)" is not selected, press
MODE
button until it is set.
(I FEEL...) → → → → → (COOL) → → → → →
(DRY)
(HEAT)
FAN STOP
I FEEL COOL
VANE START
HEAT DRY
WIDE VANE
MODE HR.
LONG
ECONO COOL MIN
Description of "I FEEL..." mode
Details of operation
According to the room temperature when the operation starts, the opera-
tion mode is automatically set to COOL, DRY or HEAT. However, when
operation is started again within 2 hours after it is stopped, the same
operation mode before the operation is stopped is selected. The opera-
tion mode selected first is not changed even if the room temperature
changes. If the operation mode does not match the room condition, se-
MODE
lect the appropriate operation mode by pressing the button.
Details of auto operation
Room temperature Operation mode Target temperature
when started (initial state)
About 77 °F or higher About 75 °F
COOL
About 77 °F - 73 °F
DRY —
About 73 °F or lower About 79 °F
HEAT
NOTE
°
COOL: When the room temperature is 4 F higher than the set temperature, the set temperature may not be changed
since the air conditioner is operating to reach the target (set) temperature. In this case, please wait until
°
the room temperature drops to within 4 F of the set temperature and then change the set temperature.
°
HEAT: When the room temperature is 4 F lower than the set temperature, the set temperature may not be
changed since the air conditioner is operating to reach the target (set) temperature. In this case,
please wait until the room temperature rises to within 4
set temperature.
Details of display on the indoor unit
The operation indicator at the right side of the indoor unit indicates
the operation state.
Lighted
Operation Indicator
Not lighted
Operation indicator lamp
Indication Operation state
This shows that the air conditioner is operating to reach the
target temperature. Please wait until the target temperature
is obtained.
This shows that the room temperature is approaching the
target temperature.
Description of "AUTO RESTART FUNCTION"
I This unit is equipped with an auto restart function. When the main power is turned on, the air conditioner will start
operation automatically in the same mode as the one set with the remote controller before the shutoff of the main power.
I If the unit was set to off with the remote controller before the shutoff of the main power, it will remain stopped even after
the main power is turned on.
I If the unit was in the emergency operation before the shutoff of the main power, it will start operation, when main power
comes on, in the same mode as the one set with the remote controller before the emergency operation.
I If the unit is operated in "I FEEL ..." mode before power failure, the operation is not stored in the memory. In "I FEEL ..."
mode, the operation is decided by the initial room temperature at (re)start.
I Since the air conditioner has been shipped from the factory with the COOL mode saved in the memory for auto restart
function, it starts cooling operation when the user turns on the main power for the first time after installation.
Room temperature:
About 77 °F or higher
→ COOL
About 77 °F - 73 °F→ DRY
About 73 °F or lower
→ HEAT
°
F of the set temperature and then change the
Difference between target
temperature and room temperature
About 4 °F or more
About 4 °F or less
7