DeWalt D26500 Manual De Instrucciones página 29

Replacing the Cutting Blades (fi g. 2)
The cutting blades fitted on this tool are reversible.
If both sides are worn, the cutting blades have to be
replaced.
WARNING: Always replace the blades
simultaneously.
1. Carefully rotate the cutterhead (g) until the first
blade becomes visible.
2. Loosen the bolts (h) using the spanner supplied.
3. Pull up the side guard (i).
4. Slide the blade (j) out of its holder.
5. Reverse the blade or replace it.
6. Slide the blade into the holder. At the rebating
side (i.e. the side where the side guard is
mounted), the cutting blade must be flush with
the planing shoe.
7. Adjust the blade as described below.
8. Tighten the bolts (h).
Repeat as for the other blade.
Adjusting the Blades (fi g. 2)
1. Ensure the depth of cut is set at 0 mm.
2. Check the position of the blade (j) at both ends.
Use a flat object as a level across the planing
shoe.
3. The tip of the blade must be flush with the
planing shoe surface.
4. If adjustment is required, proceed as follows:
Turn each adjusting screw (k) in or out as
necessary until the blade tip coincides with the
planing shoe.
Adjusting the Depth of Cut (fi g. 1)
Turn the planing depth adjustment knob (d). One
revolution of the adjustment knob equals a 4.0 mm
change in depth.
One graduation corresponds to a depth of cut of
0.1 mm.
Attaching, Removing and Adjusting
the Parallel Fence (fi g. 3)
The parallel fence (l) is used for optimum tool control
on narrow workpieces. The parallel fence can be
fitted to either side of the tool.
1. Assemble the parallel fence (l) in such way that
the fence profile will provide guidance from the
front of the tool until behind the cutterhead.
2. Fit the parallel fence to the threaded hole (m)
from either side.
3. Tighten the wing bolt (n).
To remove the parallel fence, remove the wing bolt.
TO ADJUST THE PARALLEL FENCE
1. Loosen the wing nut (o).
2. Adjust the fence so that there will be just
enough area of the cutterhead left to cut the
workpiece surface.
3. Tighten the wing nut.
Attaching, Removing and Adjusting
the Rebating Depth Stop (fi g. 4)
1. Install the depth stop (p).
2. Tighten the wing bolt (q) at the desired height in
the threaded hole (m) using the scale.
To remove the depth stop, remove the wing bolt.
Fitting and Removing the Shavings
Ejector (fi g. 5, 6)
The tool can be used for both left-hand and right-
hand side shavings discharge.
For right-hand side shavings discharge (fig. 5), the
tool can be used with or without the ejector. The
ejector must be used in combination with the dust
extraction adaptor when connecting a vacuum
extractor.
1. Push the ejector (r) into the right-hand side
shavings discharge outlet (c) until it clicks in
place.
2. To remove the ejector, raise the lever (s) and pull
out the ejector.
For left-hand side shavings discharge (fig. 6), the
ejector must always be used.
1. Raise the lever (s) to open the spring-loaded
closure (t).
2. Push the ejector (r) into the left-hand side
shavings discharge outlet (c) until it clicks in
place.
3. Release the lever.
4. To remove the ejector, raise the lever and pull
out the ejector.
Dust Extraction (fi g. 7–9)
WARNING: When appropriate, connect
a dust extraction system designed
in compliance with the applicable
directives regarding dust emission.
EN G LI SH
27