Stanley SL1M09 Manual De Instruccion página 3

• When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of
this appliance.
– The cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over, snagged, or
pulled on unintentionally (especially by children).
– The extension cord should be kept dry and off the ground.
WARNING: FIRE HAZARD: Never contact combustible material to the lens and never tape or tie the switch in the on position.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• All halogen lights give off heat:
– Do not touch lens while operating.
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.
– Never place the light face down on any surface when lit, charging or not in use. Never store the light face down on any surface.
• Never look directly into the light or shine the light into another person' s eyes.
• Keep sharp objects away from lens — it is glass and can break.
• Do not immerse spotlight in water.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw spotlight. It contains glass and a sealed lead acid battery.
• Use only with the charging adapter provided with unit. Plug in the charging adapter at the spotlight first, then plug into the
charging source.
• Do not overcharge: Recharge up to 24 hours maximum.
• After charging/recharging, disconnect charging adapter or extension cord and wait 5 minutes before use.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.
• Position charging adapter cords so they do not become entangled or become a safety hazard. Keep charging adapter cords away
from sharp edges.
• Use in a dry location only.
• Except for the H3, 55 watt bulb, there are no user-serviceable parts inside. Do not attempt to disassemble any other parts of the unit.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting.
• Do not attempt to charge the unit if the charger is damaged – return the charger to manufacturer for repair or replacement.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new spotlight. Read this Instruction Manual and follow the instructions carefully
before using your new spotlight.
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE first use using the 120 volt AC charger for
24 hours. Recharge after each use. The charge status LED lights while the unit is charging and stays lit while the charger is plugged
into the 12 volt DC charging port. When the spotlight dims, the unit needs recharging.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least every 30 days.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Never place the light face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor performance.
Charging/recharging using the 120 volt AC charger
• Make sure the spotlight is off (the trigger lock is in the off position and the trigger is not depressed).
• Insert the barrel connector of the AC charger into the 12 volt DC charging port on the back of the unit. Insert the plug end into a
(powered) standard North American 120 volt 60Hz outlet.
• Charge for approximately 18 to 24 hours.
Charging/recharging using the 12 volt DC charger (optional accessory)
• Make sure the spotlight is off (the trigger lock is in the off position and the trigger is not depressed).
• Plug the barrel tip of the supplied 12 volt DC charger into the 12 volt DC charging port.
• Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.
• Charge for approximately 18 to 24 hours.
Notes:
When using a vehicle' s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the
accessory outlet.
The spotlight may be used with either charger plugged in. However, the charging function with stop until the spotlight On/Off trigger is released and the
trigger lock is disengaged.
SL1M09_L_LB_ManualENSP_080315.indd 4-5
4
OPERATING INSTRUCTIONS
Operating the spotlight
1. Disconnect from charger.
2. The On/Off trigger is located in the front of the handle of the spotlight.
3. To turn the spotlight on, squeeze the trigger.
4. To turn off the spotlight, release the trigger.
Note:
The On/Off trigger can be locked in the on position using the trigger lock bar on the side of the unit.
Locking the spotlight
To lock the spotlight in the on position, depress the On/Off trigger, then press the trigger lock bar. The spotlight will stay on until
the trigger unlock bar is pressed and the on/off trigger is released.
If the On/Off trigger is released when the trigger lock bar is pressed, the spotlight will be locked in the off position. To turn the
spotlight on again, press the trigger unlock bar before pressing the On/Off trigger.
Using the carry lanyard (optional accessory)
The carry lanyard may be used to carry the unit or to hang it for storage. Always adjust the slide on the cords to keep the lanyard
secure around any supporting object.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is hung by the carry lanyard, do not shake the spotlight or object that it is hanging from. Do not hang the spotlight
from any electrical wires or anything that it is not secure.
• Only use the carry lanyard for hanging this spotlight. The carry lanyard is not intended to support additional weight. Do not attach
or hang anything additional to the spotlight or risk of breakage may occur.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with
a mild solution of water and detergent.
Except for the H3, 55 watt bulb, there are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and
wires. Contact manufacturer to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to
the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any
information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly.
Recycling is required. Failure to comply with local, state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
Spotlight Bulb Replacement
To replace the bulb, you will need a small Phillips screwdriver and a 6 volt, H3 55 watt replacement bulb. During installation, avoid
touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be
wiped clean with a cloth moistened with alcohol.
1. Disconnect the unit from any charging adapters.
2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in the retaining ring.
3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.
4. Lift off the retaining ring, glass lens and rubber "O" ring and set them aside.
5. Carefully remove the reflector and bulb assembly.
6. Disconnect the bulb wire from the red power wire.
7. Unsnap the hairpin retaining wires from the reflector' s flange.
8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely remove this
screw).
5
8/3/2015 12:15:11 PM