DeWalt DWE402 Manual De Instrucciones página 10

Esmeriladora angular pequeña con interruptor de paleta para trabajos pesados
Ocultar thumbs Ver también para DWE402:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
Fig. C
13
setting guard Adjustment Options
To adjust the guard release lever 
adjustment option:
1. Remove screw 
using a T20 bit.
 12 
2. Remove the guard release lever taking note of the
spring position. Choose the end of the lever for the
desired adjustment option. One-touch will use the
slanted end of the lever 
 7
holes 
 14 
on the guard collar. Two-touch will use the
squared end to engage the alignment holes 
guard collar.
3. Replace the lever, positioning the chosen end under the
spring 
 13 
. Ensure the lever is in proper contact with
the spring.
4. Replace screw and torque to 2.0-3.0N-m. Ensure proper
installation with spring return function by depressing
guard release lever 
.
 7 
Mounting guard (Fig. D)

CAUTION: Prior to mounting guard, ensure the screw,
lever, and spring are fitted correctly before mounting
the guard.
1. With the spindle facing the operator, press and hold the
guard release lever 
 7 
.
2. Align the lugs 
 15 
on the guard with the slots 
the gear case cover.
3. Push the guard down until the guard lugs engage
and rotate them in the groove on the gear case cover.
Release the guard release lever.
4. To position the guard:
One-touch
TM
: Rotate the guard clockwise into the
desired working position. Press and hold the guard
release lever 
 7 
to rotate the guard in the counter-
clockwise direction.
Two-touch
: Press and hold the guard release
TM
lever 
 7 
. Rotate the guard clockwise or counter-
clockwise into the desired working position.
8
12
7
 7 
for desired
to engage the alignment
on the
 14 
 16 
on
nOTE: The guard body should be positioned between
the spindle and the operator to provide maximum
operator protection.
The guard release lever should snap into one of the
alignment holes 
on the guard collar. This ensures
 14 
that the guard is secure.
5. To remove the guard, follow steps 1–3 of these
instructions in reverse.
Fig. D
14
16
Flanges and Wheels

CAUTION: Turn unit off and unplug the tool before
making any adjustments or removing or installing
attachments or accessories.
Mounting Non-Hubbed Wheels
(Fig. E, F)

WARNING: Failure to properly seat the flanges and/or
wheel could result in serious injury (or damage to the
tool or wheel).

CAUTION: Included flanges must be used with
depressed center Type 27/42 grinding wheels and
Type 1/41 cutting wheels. See the Accessories Chart
for more information.

WARNING: A closed, two-sided cutting wheel guard
is required when using abrasive cutting wheels or
diamond coated cutting wheels.

WARNING: Use of a damaged flange or guard or fail-
ure to use proper flange and guard can re sult in injury
due to wheel breakage and wheel contact. See the
Accessories Chart for more information.
1. Place the tool on a table, guard up.
2. Install the unthreaded backing flange 
with the raised center (pilot) facing the wheel.
3. Place wheel 
 17 
against the backing flange,
centering the wheel on the raised center (pilot) of the
backing flange.
4. While depressing the spindle lock button and with the
hex depressions facing away from the wheel, thread the
threaded locking flange 
 4 
engage the two slots in the spindle.
15
7
 3 
on spindle 
 1 
on spindle so that the lugs

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dwe402nDwe402gDwe4222nDwe43114, dwe43114nDwe43144Dwe43144n

Tabla de contenido