Saber R33SC0012 Manual De Uso página 7

Main Burner Ignitor Lighting
Do not lean over grill while lighting.
1. Turn OFF all control knobs.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. To ignite, push and turn burner control knob to
5. Push and hold ELECTRONIC IGNITION button until the burner
lights (use flame viewing ports to verify).
6. If ignition does NOT occur in 5 seconds, turn the burner controls
OFF, wait 5 minutes, and repeat the lighting procedure.
7. Ignite remaining burners by repeating steps 4 through 6 for each
burner.
8. Once each burner has ignited, turn knobs to desired setting.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
controls knobs OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Main Burner Match-Lighting
Do not lean over grill while lighting.
1. Turn OFF all control knobs.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. Place match into match holder (hanging from left side of cart).
Light match, place into lighting hole on left side of firebox.
5. Push in and turn far left control knob to
burner has ignited (use flame viewing ports to verify), turn
control knob to desired setting.
6. If ignition does NOT occur in 5 seconds, turn the control knob
OFF, wait 5 minutes, and repeat the lighting procedure.
7. Light adjacent burners in sequence by pushing control knob
in and turning to position.
Burner Flame Check
Remove cooking grates and emitters. Light burners, rotate control

knobs from HI to LO. You should see a smaller flame in LO
position than seen on HI. Perform burner flame check on side
burner, also. Always check flame prior to each use. If only low
flame is seen refer to "Sudden drop or low flame" in the
Troubleshooting Section.
Turning Grill Off
Turn all control knobs to OFF position. Turn LP cylinder OFF by

turning hand-wheel clockwise to a full stop.
Ignitor Check
Turn Gas OFF at LP cylinder. Press and hold electronic ignition

Viewing ports button. "Click" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
IMPORTANT: Make sure gas is OFF at LP cylinder before

checking valves. Control knobs lock in OFF position. To check
valves, first push in control knobs and release, control knobs
should spring back. If control knobs do not spring back, replace
valve assembly before using grill. Turn control knobs to LO
position then turn back to OFF position. Valves should turn
smoothly.
Hose Check
Before each use, check to see if hoses are cut or worn. Replace

damaged hoses before using grill. Use only valve/hose/regulator
specified by manufacturer.
Quick Start Tips
Preheating for different types of grilling:
Sear - preheat with all burners set to HI for maximum cooking

grate temperatures
Barbecue - preheat with all burners set to LO for a lower starting

grate temperature for grilling foods slower.
Indirect grilling - preheat one burner only on the side opposite

where the food will be placed to allow the slowest and lowest
position. Once
grilling for larger cuts of meat.
Roasting - place the warming rack on the lower supports and

use burner(s) directly under the food on LO or indirectly for lower
temperature cooking. This will allow more heat to circulate
around the food during grilling.
Lowering the temperature of the cooking grate:
Control knob - turn the control knob to the LO setting for the

lowest temperature setting.
Control knob - for the lowest cooking grate temperatures the

food can be grilled indirectly with the burner under the food in the
OFF position and a single burner away from the food on LO.
During grilling the grill can be cooled down faster by lifting the lid

while adjusting the control knobs to a lower setting.
HI
LO
7