Programming The Timer; Time Setting - Dörr KOMPAKT X12M Manual De Instrucciones

07 | PROGRAMMING THE TIMER

Open the timer compartment (1) pressing the compartment cover (2)
upward and drawing the fl ap outwards. Slide the On/O switch (11) to
position ON.

07.1 TIME SETTING

After you have set the On/O switch (11) to the ON position, the hour in-
dicator starts blinking. Use the +/- buttons (9) to adjust the hour (12-hour
format).
After 6 sec., the minute display starts blinking. Use the +/- buttons (9) to
set the minutes. After another 6 sec. the weekday can be set using the +/-
buttons (9). Wait for 6 sec. and the programming of time, date and weekday
is done.
07.2 SETTING THE FEEDING TIMES
Up to 16 feeding times can be programmed for each weekday. Proceed
as follows:
Press the PROG button (10). The display (7) shows Mo for Monday and the
number 1 for the fi rst feeding time. After 6 sec. you can enter the hour with
the +/- buttons (9) and after another 6 sec. you can enter the minutes.
After entering the time Mo is blinking. Press the +/- buttons (9) to set the
weekdays, the feeder should start to feed at fi rst feeding time.
It is possible to select each weekday separately or you can choose one of
the following pre-settings:
Monday to Sunday
•
Monday to Friday
•
Saturday and Sunday
•
Monday to Saturday
•
Monday, Wednesday, Friday
•
Tuesday, Thursday, Saturday
•
Monday to Wednesday
•
Thursday to Saturday
•
Monday, Wednesday, Friday, Sunday
•
After 6 sec. the selected setting is programmed and in the display the num-
ber 30 is blinking. Now you can set the desired duration of the feeding from
30 to 1 second using the +/- buttons (9).
After further 6 sec. the fi rst feeding time is set and the display (7) shows the
main menu with the present time.
To select further feeding times, press the PROG button (10) again and then
the + button (9). In the display (7) the number 2 is blinking. Now you can
enter a second feeding time like described above.
For further 3-16 feeding times please repeat the setting accordingly.
07.3 TEST FUNCTION
After installation of the feeder, this function allows checking if the feeding
time, quantity and range of feeding are correct – depending on the type
of feed.
Press the TEST button (8). The display (7) shows TEST and the number 30
(indicates the length of test feeding in seconds).
Use the +/- buttons (9) to set the duration of the test feeding from 30 to
1 seconds.
Note
We recommend a max. test duration of 1-2 seconds, so only a small
quantity of feed is spread for testing purposes.
Confi rm the test duration with the TEST button (8). The test feeding will
start within 3 seconds.
CAUTION
for both test and regular operation. Protect your eyes and
extremities! The fast rotation of the feeding engine and the
ejected feed can be harmful.
08 | DISPERSE QUANTITY
Example: corn (full grain max. 5% fracture)
Feeding duration
1 sec.
2 sec.
Mo = Monday
5 sec.
Di = Tuesday
10 sec.
Mi = Wednesday
15 sec.
Do = Thursday
20 sec.
Fr = Friday
25 sec.
Sa = Saturday
30 sec.
So = Sunday
As rule of thumb: Each second about 0,5 litres strewn.
09 | RESET
Pressing the RESET button (12) the feeder will be set back to factory set-
tings. This will also happen, if the feeder is switched o for more than 5
seconds. Thereafter timer and feeder programming must be renewed.
Note
We recommend noting the desired feeding times in order to simplify repeat
programming.
10
Keep a distance of minimum 7m from the feeder
Disperse quantity in kg
approx. 0,34 kg
approx. 0,7 kg
approx. 1,7 kg
approx. 3,4 kg
approx. 5,1 kg
approx. 6,8 kg
approx. 8,5 kg
approx. 10,2 kg
equivalent to litre
approx. 0,5 l
approx. 1,0 l
approx. 2,3 l
approx. 4,8 l
approx. 7,1 l
approx. 9,6 l
approx. 11,9 l
approx. 14 l