Programming The Timer; Time Setting - Dörr KOMPAKT X42 Manual De Instrucciones

1. Open the battery compartment (4) pressing the compartment cover (5)
upward and drawing the flaps outwards.
2. Slide the plugs of the battery cables (6) onto the corresponding battery
contacts.
CAUTION Make sure to respect the correct polarity: red
cable (+) to red battery contact, black cable (-) to black
battery contact.
3. Place the battery in the battery compartment (4) and close the com-
partment cover (5).
Note
When changing the battery, we suggest leaving the feeder main switch
(11) in position ON in order to avoid the loss of settings.
Please note that batteries often are not fully charged when purchased.
We recommend checking and if necessary charging the battery before
starting operation. Use a customary charger.
SAFETY HINTS FOR RECHARGEABLE BATTERIES
Only use high-quality batteries of popular brands. When inserting the bat-
tery please respect the correct polarity (+/-). Please remove battery when
device is not in use for a long period of time. Do not throw the batteries
into fire, do not short-circuit and do not disassemble them – risk of explo-
sion! Remove leaking batteries from the device immediately. Risk of battery
acid burn! Clean the contacts before inserting fresh batteries. In case of
contact with battery acid, rinse the affected area immediately with water
and contact a doctor. Batteries can be dangerous to life if swallowed. Keep
batteries away from small children and pets. Do not dispose of batteries in
household waste (see also capture "Disposal of Batteries/Accumulators").

06 | PROGRAMMING THE TIMER

Open the timer compartment (1) pressing the compartment cover (2)
upward and drawing the flap outwards. Slide the On/Off switch (11) to
position ON.

06.1 TIME SETTING

After you have set the On/Off switch (11) to the ON position, the hour in-
dicator starts blinking. Use the +/- buttons (9) to adjust the hour (12-hour
format).
After 6 sec., the minute display starts blinking. Use the +/- buttons (9) to
set the minutes. After another 6 sec. the weekday can be set using the +/-
buttons (9). Wait for 6 sec. and the programming of time, date and weekday
is done.
06.2 SETTING THE FEEDING TIMES
Up to 16 feeding times can be programmed for each weekday. Proceed
as follows:
Press the PROG button (10). The display (7) shows Mo for Monday and the
number 1 for the first feeding time. After 6 sec. you can enter the hour with
the +/- buttons (9) and after another 6 sec. you can enter the minutes.
After entering the time Mo is blinking. Press the +/- buttons (9) to set the
weekdays, the feeder should start to feed at first feeding time.
It is possible to select each weekday separately or you can choose one of
the following pre-settings:
Monday to Sunday
•
Monday to Friday
•
Saturday and Sunday
•
Monday to Saturday
•
Monday, Wednesday, Friday
•
Tuesday, Thursday, Saturday
•
Monday to Wednesday
•
Thursday to Saturday
•
Monday, Wednesday, Friday, Sunday
•
After 6 sec. the selected setting is programmed and in the display the num-
ber 30 is blinking. Now you can set the desired duration of the feeding from
30 to 1 second using the +/- buttons (9).
After further 6 sec. the first feeding time is set and the display (7) shows the
main menu with the present time.
To select further feeding times, press the PROG button (10) again and then
the + button (9). In the display (7) the number 2 is blinking. Now you can
enter a second feeding time like described above.
For further 3-16 feeding times please repeat the setting accordingly.
06.3 TEST FUNCTION
After installation of the feeder, this function allows checking if the feeding
time, quantity and range of feeding are correct – depending on the type
of feed.
Press the TEST button (8). The display (7) shows TEST and the number 30
(indicates the length of test feeding in seconds).
Use the +/- buttons (9) to set the duration of the test feeding from 30 to
1 seconds.
Note
We recommend a max. test duration of 1-2 seconds, so only a small
quantity of feed is spread for testing purposes.
Confirm the test duration with the TEST button (8). The test feeding will
start within 3 seconds.
CAUTION Keep a distance of minimum 7m from the feeder
for both test and regular operation. Protect your eyes and
extremities! The fast rotation of the feeding engine and the
ejected feed can be harmful.
08
Mo = Monday
Di = Tuesday
Mi = Wednesday
Do = Thursday
Fr = Friday
Sa = Saturday
So = Sunday