Battery Charger Safety; Product Familiarisation; Intended Use - Silverline 326579 Manual Del Usario

GB

Battery Charger Safety

Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before
attempting to charge the battery.
• Do not attempt to use the charger with any batteries other than those supplied. Keep
your battery charger clean; foreign objects or dirt may cause a short or block air vents.
Failure to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard
• Examine the battery charger regularly for damage, especially the cord, plug and
enclosure. If the battery charger is damaged, it must not be used until it has been
repaired
• Children should be supervised to ensure that they do not play with the appliance
WARNING: DO NOT attempt to recharge non-rechargeable batteries.
Battery and charger safety features
The battery and charger are fitted with a number of safety features which may be triggered
during charging or operation:
• Over-charge protection: Charger automatically switches off when the battery has
reached full charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the battery from discharging beyond the
recommended lowest safety voltage
• Over-heat protection: Sensor switches off if the battery becomes too hot during
operation. This can happen if the tool is overloaded or being used for extended periods
of time. Up to 30 minutes cooling time may be required depending on the ambient
temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum
current draw is exceeded, protecting the internal components. The battery will resume
normal operation when the current draw returns to a normal safe level. This may take a
few seconds
• Short circuit protection: The battery will stop working immediately if a short circuit
occurs, this prevents damage to the battery or tool
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries provided with this
power tool, or others recommended by the supplier
• Keep batteries clean; foreign objects or dirt may cause a short
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow
these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approx 20˚C). Ensure
that batteries cannot accidentally short in storage.
Battery Safety
WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a fire, burn and
explosion hazard.
• Keep the battery out of reach of children
• ONLY charge Li-Ion batteries designed specifically for this charger
• ONLY use Li-Ion batteries provided with this product or specifically designed to be
compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow
these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure battery contacts cannot accidentally short in storage. Keep batteries clean;
foreign objects or dirt may cause a short. Keep away from other metal objects, for
example paperclips, coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause
skin irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
• DO NOT open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in
fire or similar
6

Product Familiarisation

1 Chuck Jaws
2 Chuck Collar
3 Torque Selector
4 Motor Vents
5 Forward/Reverse Switch
6 Main Handle
7 Battery
8 Battery Release
9 Battery Slot
10 Trigger Switch
11 LED Worklight
12 LED Charge Indicator
13 Battery Charger
14 Battery Contacts
15 Green LED
16 Red LED
17 Charger PSU
18 Charger DC plug

Intended Use

General-purpose cordless power drill for screwdriving and drilling applications (excluding
masonry). This drill is optimally configured for screw-driving applications.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool
Before Use
Removing the battery from the drill
• To remove the Battery (7) from the drill, press the Battery Release (8) and pull the
Battery forwards out of the Battery Slot (9) at the base of the drill
Installing a charged battery
1. To fit a charged Battery (7) to the drill, slide it into the Battery Slot (9)
Note: The Battery will fit only in one direction, which is determined by its shape and the
design of the battery housing. However, if the Battery does not slide into the housing easily,
do not force it. Instead, pull the Battery out of the housing again, check for correct position,
and try again gently.
2. Push the Battery into the battery housing in the handle until it locks into place securely
Note: The drill features an LED Charge Indicator (12) which operates when the Trigger
Switch (10) is pressed. 3 LEDs indicate a high charge, 1 LED indicates a low charge and
the Battery will need charging soon.
Setting up the charger
1. If fitted, remove the Battery (7) from the Battery Slot (9)
2. Connect the Charger DC Plug (18) to the DC socket at the rear of the Battery
Charger (13)
3. Connect the Charger PSU (17) to the mains power supply
Note: The green LED on the Battery Connector will illuminate to indicate that Charger is
powered.
WARNING: Only use this Charger to charge the supplied Battery.
WARNING: The Battery Charger is designed for indoor use only and must not be exposed
to moisture and rain.