Product Familiarisation; Battery & Charger Safety; Intended Use; Unpacking Your Tool - Silverline 975325 Manual De Instrucciones

GB
j) Drill bits get hot during operation, allow to cool prior to handling them.
k) NEVER use your hands to remove sawdust, chips or waste close by the bit.
l) If you are interrupted when operating the drill, complete the process and switch off
before looking up.
m) Where possible, use clamps or a vice to hold your work.
n) Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired by
a qualified service centre.
o) ALWAYS wait until the drill has come to a complete stop before putting it down.
p) Periodically check all nuts, bolts and other fixings and tighten where necessary.
q) Even when this tool is used as prescribed it is not possible to eliminate all residual risk
factors. If you are in any doubt as to the safe use of this tool, do not use it.
Battery & Charger Safety
Use the Battery Charger correctly
• Refer to the section of this manual relating to use of the Battery Charger (14) before attempting
to charge the Battery (10)
• Do not attempt to use the battery charger with any batteries other than those supplied. Keep your
battery charger clean; foreign objects or dirt may cause a short or block air vents. Failure to follow
these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard
• Examine the battery charger regularly for damage, especially the cord, plug and enclosure. If the
battery charger is damaged, it must not be used until it has been repaired
• Children should be supervised to ensure that they do not play with the appliance
WARNING: Do not attempt to recharge non-rechargeable batteries.
Battery Safety
WARNING: Li-ion batteries, if incorrectly used, stored or charged are a fire, burn and explosion
hazard.
• Keep the battery out of reach of children
• Only charge Li-ion batteries designed specifically for this charger
• Only use Li-ion batteries provided with this product or specifically designed to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these
instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure battery contacts cannot accidentally short in storage. Keep batteries clean; foreign objects
or dirt may cause a short. Keep away from other metal objects, for example paperclips, coins,
keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause skin
irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, seek medical help
• Do not open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in fire or
similar
• Do not get batteries wet or immerse in water
Battery & charger safety features
The Battery and Charger are fitted with a number of safety features which may be triggered during
charging or operation:
• Over-charge protection: Charger automatically switches off when the Battery has reached full
charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the Battery from discharging beyond the recommended
lowest safety voltage
• Over-heat protection: Sensor switches off if the Battery becomes too hot during operation.
This can happen if the tool is overloaded or being used for extended periods of time. Up to 30
minutes cooling time may be required depending on the ambient temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current draw is
exceeded, protecting the internal components. The Battery will resume normal operation when
the current draw returns to a normal safe level. This may take a few seconds
• Short circuit protection: The Battery will stop working immediately if a short circuit occurs, this
prevents damage to the Battery or tool
6

Product Familiarisation

1. Chuck Jaws
2. Chuck Collar
3. Torque Selector
4. Motor Vents
5. On-Tool Battery Charge Indicator
6. Forward/Reverse Switch
7. Main Handle
8. Battery Charge Indicator
9. Battery Mount
10. Battery
11. Battery Release
12. LED Work Light
13. ON/OFF Trigger Switch
14. Battery Charger
15. Charger Terminals
16. Green LED
17. Red LED

Intended Use

Battery-operated combi hammer drill with screwdriver, drill and impact drill functions suitable for
medium duty drilling and driving tasks. Includes hammer/impact function for light masonry drilling.
The tool must ONLY be used for its intended purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The operator, and not the manufacturer, shall be liable
for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable
for any modifications made to the tool, nor for any damage resulting from such modifications.

Unpacking Your Tool

• Carefully unpack and inspect your product. Fully familiarise yourself with all its features and
functions
• Ensure all parts of the product are present and in good condition
• If any parts are missing or damaged, have such parts replaced before attempting to use this
product

Before Use

Removing the Battery
• To remove the Battery (10), press the Battery Release (11) and slide the Battery out of the Battery
Mount (9) (Fig. I (a-b))
Installing a charged Battery
1. To fit a charged Battery (10), slide it into the Battery Mount (9) (Fig. I (c))
Note: The Battery will fit only in one direction, which is determined by its shape and the design
of the Battery Mount. However, if the Battery does not slide into the Battery Mount easily, do not
force it. Instead, pull the Battery out of the Battery Mount again, check for correct position, and try
again gently.
2. Push the Battery into the Battery Mount until it locks into place securely