Tabla de contenido
Publicidad
b) Do not position your body in line with and
behind the rotating wheel. When the wheel, at the
point of operation, is moving away from your body,
the possible kickback may propel the spinning wheel
and the power tool directly at you.
c) When wheel is binding or when interrupting a
cut for any reason, switch off the power tool and
hold the power tool motionless until the wheel co-
mes to a complete stop. Never attempt to remove
the cut-off wheel from the cut while the wheel is in
motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of
wheel binding.
d) Do not restart the cutting operation in the work-
piece. Let the wheel reach full speed and carefully
re-enter the cut. The wheel may bind, walk up or
kickback if the power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on
both sides of the wheel.
f) Use extra caution when making a "pocket cut"
into existing walls or other blind areas. The pro-
truding wheel may cut gas or water pipes, electrical
wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding
paper extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing of
the disc or kickback.
Additional Safety and Working Instructions
When grinding metal, flying sparks are produced.
Take care that no persons are endangered. Because
of the danger of fire, no combustible materials
should be located in the vicinity (spark flight zone).
Do not use dust extraction.
Avoid flying sparks and sanding dust hit your body.
Never reach into the danger area of the machine
when it is running.
Chips and splinters must not be removed while the
machine is running.
Immediately switch off the machine in case of con-
siderable vibrations or if other malfunctions occur.
Check the machine in order to find out the cause.
Do not let any metal parts reach the airing slots -
danger of short circuit!
Under extreme conditions (e.g. smooth-grinding
metals with the arbour and vulcanized fibre grinding
wheel), significant contamination can build up on the
inside of the angle grinder. For safety reasons, in such
conditions the inside should be cleaned thoroughly
of metal deposits and a motor circuit-breaker must be
connected in series. If the motor circuit-breaker trips
the machine must be sent for repair.
For accessories intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel is
long enough to accept the spindle length.
Always use and store the cutting and grinding disks
according to the manufacturer's instructions.
Always use the correct guard for cutting and grin-
ding.
Always use guard with cutting guide from the acces-
sories range for cutting stone.
The adjusting nut must be tightened before starting
to work with the machine.
Always use the auxiliary handle.
The workpiece must be fixed if it is not heavy enough
to be steady. Never move the workpiece towards the
rotating disk by hand.
STARTUP PROTECTION
58107: Machines with a lockable switch are supplied
with a restart cutout. This prevents the machine rest-
arting by itself after a power failure. When resuming
work, switch the machine off and then switch it back
on again.
Mains Connection
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to single-phase AC system voltage as
indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as
the design conforms to safety class II.
Only plug-in when machine is switched off.
Maintenance
Unplug the machine before any work on it.
Repairs and works specified in these Instructions may
only be performed by qualified authorised staff.
Use only original accessories and original spare parts.
Keep the device, in particular the air vents, clean at all
times. Never spray water on the device body!
Do not clean the plastics with solvents, flammable or
toxic fluids. For cleaning, use a damp cloth only.
Caution! If the power cord of the appliance gets
damaged, it must be replaced by the manufacturer or
its customer service or a similarly qualified person to
avoid danger.
Only a regularly maintained and treated appliance
can serve as a satisfactory aid. Insufficient mainte-
nance and care can lead to unforeseen accidents and
injuries.
If necessary, a list of spare parts can be found at www.
guede.com.
ENGLISH
17
Publicidad
Tabla de contenido
