HK Audio PR:0 110 XD2 Manual Del Usuario página 6

PREMIUM PR:O D2 1.0
2 PREMIUM PR:O Self-powered
Subwoofers
PR:O 118 SUB D2 • PR:O 210 SUB D2
2.1 Control Features
●
1
Line Out Mid/High L/R
Two electronically balanced XLR outputs for connecting PREMIUM PR:O
mid/ high units (pin 1 = ground, 2 = +, 3 = -).
●
2
Input L/R
These two electronically balanced XLR / 1/4" combi inputs accept signals
from mixing consoles (pin 1= ground, 2= +, 3= -).
●
3
Thru L/R
These two parallel outputs patch incoming line signals through, for
example, to other PREMIUM PR:O active speakers or monitors
(pin 1= ground, 2= +, 3= -).
●
4
Gain Bass
This knob adjusts the input level (center position = 0 dBV). The 12 o'clock
position is the ideal starting point when operating the subwoofer in
combination with a PREMIUM PR:O active cabinet. Then you can simply
twist the knob to the left or right to cut and boost bass frequencies. If you
connect a PREMIUM PR:O satellite, fi rst set the Gain knob to the center
detent and then adjust the level to suit the given sound reinforcement
situation.
●
5
X-Over Bass
The active crossover can serve to vary the top cutoff frequency of the
subwoofer with a range of 75 to 150 Hz. The best cutoff frequency for the
given application depends on the surroundings and satellite, so you will
have to experiment.
Note: If you set the cutoff to a frequency higher than 100 Hz, the
subwoofer will render mostly the lower frequencies of signals generated
by bass guitars, kick drums, and low-end keyboard sounds. If you set the
cutoff to a frequency higher than 100 Hz, the subwoofer will also render
the lower frequencies of voices and other sound sources.
●
6
Phase
The Phase switch changes the subwoofer's phase position to match it to
the connected satellite's phase position (0°/180°). Set the switch to 0°
when operating in combination with a PREMIUM PR:O active cabinet.
You may have to invert the phase for combinations with other enclosures.
If you are unsure, simply try the 180° setting. If the bass response changes
and the signal sounds weak and washed out, the phase setting is incorrect.
●
7
Limiter/Status LED
This dual-color LED serves as a status indicator for the PREMIUM PR:O
powered cabinet (green = power on, red = limit/error). The LED briefl y
fl ashes red to tell you the limiter is responding to signal peaks.
Caution! If the Status LED stays red during operation, the cabinet is being
overloaded. Turn down the signal level! If you are not routing a signal in
and the Status LED stays red, the system has detected a fault.
6
All manuals and user guides at all-guides.com
7
Line Out Mid/High
8
1 1
Power
L R
Input
Gain Bass
4
2 2
Phase
L R
0°
Thru
10
X-Over Bass
Auto
5
Stand-by
3 3
On
75 Hz
Off
L R
PREMIUM PR:O
118 Sub D2
9
Mains Caution: To reduce
the risk of electric
100-240 V~
shock, grounding
50-60 Hz of the center
1 A @ 1/8 pin of this plug
must be
output power
maintained.
Line Out Mid/High
L
1
PREMIUM PR:O
210 Sub D2
Input
2 2
L
Thru
3 3
Gain Bass
X-Over Bass
7
75 Hz 150 Hz
Green = On
Red = Limit/Error
Phase
Power
On
8
Off
Mains
220-240 V~
50-60 Hz
0.4 A @ 1/8 output power
9
Caution: To reduce the risk
of electric shock, grounding
of the center pin of this
plug must be maintained.
Green = On
Red =
Limit/Error
On
Off
6
180°
150 Hz
R
1
R
4
5
6
180°
0°