Technical Characteristics - PRESIDENT LINCOLN II + Manual Del Usuario

Ocultar thumbs Ver también para LINCOLN II +:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

At [
] menu, rotate PUSH knob (6) to
Voltage range:
~ 1
V, stepping:
90U
70U
to change the step. The HIGH limit is useful only if the VOLTAGE protection
function is active.
11) VOLTAGE PROTECTION LOW
Set
the LOWER LIMIT of VOLTAGE PROTECTION.
At [
] menu, rotate PUSH knob (6) to
Voltage range:
~ 1
V, stepping:
90U
70U
to change the step. The LOW limit is useful only if the VOLTAGE protection
function is active.
12) SCAN TYPE
Select
the TYPE of SCAN.
At [
] menu, rotate PUSH knob (6) to
"
"means scanning stops when busy channel is founded.
" " means scanning stops when busy channel is founded and return to scan
after 5 seconds.
13) BACKLIGHT COLOR
Select
the BACKLIGHT COLOR of the unit.
At [
] menu, rotate PUSH knob (6) to
Three colors are possible "
" (orange/default), "
14) BACKLIGHT BRIGHTNESS
Adjust
the BACKLIGHT BRIGHTNESS of the unit.
At [
] menu, rotate PUSH knob (6) to
Brightness level: 1 ~ 9, default: 9.
15) s/t KEYS SETTING
Select
the UP/DOWN KEY feature.
At [
] menu, rotate PUSH knob (6) to
"
" means s/t keys changes CHANNEL (default).
"
" means s/t keys changes FREQUENCY.
Note: If FREQUENCY is selected. Press PUSH knob (6) to select the frequency
digit to be increased by the s/t keys.
16) DW SETTING
Set
the CHANNEL use with DUAL WATCH function.
At [
] menu, press BAND key (21) to
key (18) to select desired modulation mode, rotate PUSH knob (6) to
set
the High limit.
. Press PUSH knob (6)
, default: 1
01U
70U
set
the Low limit.
, default:
. Press PUSH knob (6)
01U
90U
select
the Type.
select
the Color.
" (green) or "
" (blue).
select
the BRIGHTNESS.
select
the Feature.
select
desired band, press MODE
select
channel. Default: band: I - modulation: FM - channel: 09.
See DUAL WATCH function, page 33.
17-18) PRIORITY CHANNEL SETTING
Configure
the priority channels. In the [
ton (21) to
select
the desired band, press the MODE button (18) to
desired modulation mode, turn the PUSH button (6) to
channel. Press the PUSH button (6) to
Same procedure for the second priority channel in the [
channels 9 and 19 are; the default channels.
See the EMG 1/2 function page 33.
19) CTCSS / DCS SETTING
Set
the operating mode of CTCSS/DCS.
In the menu [
], rotate the PUSH knob (6) to
mode of CTCSS and DCS.
In "
" mode, the value (of tone and code) is equivalent for transmission
and reception (default mode).
In "
" mode, the value (of tone and code) for transmission can be different
(unlike) from the one of reception.
See function CTCSS/DCS page 33.
20) RESET
Initialization
of the unit.
select
At [
] menu,
"
" for all functions and channels setting initialized.
Short press PUSH knob (6) to confirm. Wait until LCD shows "
D) TECHNICAL CHARACTERISTICS
1) GENERAL
- Modulation modes
- Frequency ranges
- Antenna impedance
- Power supply
- Dimensions (in mm)
- Weight
- Accessories supplied
36
] menu, press the BAND but-
select
the first priority
confirm
and store.
select
the operating
"
" for all functions setting initialised,
: AM / FM / USB / LSB / CW
: from 28.000 MHz to 29.700 MHz
: from 24.880 MHz to 24.980 MHz
: 50 ohms
: 13.2 V
: 170 (W) x 250 (D) x 52 (H)
: 1,4 kg
: microphone UP/DOWN with support,
mounting cradle, screws and fused
power cord.
select
the
] menu. The
select
".

Publicidad

Tabla de contenido
loading

Tabla de contenido