stayer S110PE Manual De Instrucciones página 20

Pendular stroke setting
S110PE/S110PEK/S111PEK/JS80PE
When set to the pendular stroke, there will be a forward and
backward movement in addition to the up and down
movement of the saw blade. Through this, the saw
accelerates and the saw blade will be protected from
damage.
• Set the switch 0 / I / II / III (9) to one of the following
positions:
Position Pendular motion Material
0 No pendular Rubber, ceramic,
motion aluminium, steel
Low Plastic, wood,
I
pendular motion aluminium
II Medium Wood
pendular motion
III Large Wood
pendular motion
Tip: The best combination of stroke rate and pendular
stroke setting is dependent upon the workpiece. We
recommend to perform a test run on a piece of scrap
material. This way the most appropriate setting can be
found.
Setting the stroke rate
The stroke rate indicates the number of the up and down
movements per minute of the saw blade. The required
stroke rate depends on the work load and workpiece. On
one hand, an adequate working speed should be reached,
on the other, a clean cut should be achieved.
• Select the desired speed with the turning knob (4):
• To increase the speed turn the knob counterclockwise.
To decrease the speed turn the knob clockwise.
• With fine saw blades a higher stroke rate can be used;
rough saw blades require lower speed.
• After using the jigsaw for a longer period with a high
stroke rate, the power tool can heat up intensely - allow
the power tool to cool down for 3 minutes running idle at
maximum speed.
Straight cut ( ill. F)
When using the jigsaw to perform straight cuts, remember
to attach the cover (21), plastic guide (22) and the plastic
sawfoot cover (28). The use of the plastic guide (22) will
prevent the sawblade from swinging during the cut.
Angle cut
Setting the cutting angle ( ill. D/F)
• The preset angle between the saw foot (7) and saw blade
(11) is 90°. You can adjust this angle on both sides gradually
to 15°/30°/45° using angle scale (28) as reference.
All manuals and user guides at all-guides.com
ENGLISH
15
Danger of accidents!
• Pull out the power plug (5) from power outlet before setting
the angle cut.
• The teeth of the saw blades are very sharp!
• Use the large allen key (17) to set the sawing angle.
• Loosen the tightening screw (26) with the allen key far
enough so that the saw foot (7) can be easily turned.
• For straight cuts (0°) the angle scale (28) should be set to
0°. For angle cuts set the scale to value between 1° and 45°.
• Set the saw foot to the desired position 15°/30°/45° on the
angle scale (28).
Comment
• After the angle is set push the saw foot (7) down until is
For fine/clean cutting
locked in place.
edges, thin materials
• Retighten the tightening screw (26) with the large allen key
(i.e. laminations),
(17).
hard materials
Hard materials
Dip sawing ( ill. E)
Only soft working materials, such as wood or plaster
cardboard, may be used for dip sawing! For dip sawing, only
use short saw blades and always set the sawing angle to 0°.
Soft materials,
saw along the
• Place the peak of the saw blade (11) and the front parts of
fiber direction
• Switch the jigsaw on and allow the saw blade to run.
• Slowly reduce the angle of support of the saw foot in the
• As soon as the saw foot lies smoothly on the workpiece,
Sawing out areas
• With a drill, drill a sufficiently large hole inside of the area to
be sawed out.
• Guide the saw blade (11) into this hole and begin to saw
out the desired area.
• Use the laser guide (14) to obtain more precise cuts.
Mounting the parallel guide
The parallel lines can be sawed with miter-precise intervals
using a parallel guide (19). Parallel cuts are only available
when the angle of the saw foot is set to 0° and the plastic
cover for sawfoot (27) is removed.
• Using screwdriver loosen the tightening screw of the
parallel guide (20).
• Push the parallel guide into the guideway opening (24).
The parallel guide can be inserted in the left or right side of
the power tool.
• Align the guide rail and retighten the tightening screw (20).
Laser guide
S110PE/S110PEK/S111PEK/JS80PE
The built-in laser guide is intended to obtain a precision cut.
Use the laser guide (14) every time the work requires
precision cuts, as when following pre-drawn lines on a
surface.
15
the saw foot (7) on the workpiece.
direction of the workpiece. The saw blade „dips" into the
area to be cut out. At this time, the power tool may not be
moved sideways.
you can begin sawing.