Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted to the
original purchaser only to be free from defects in material and workman-
ship. Subject to certain exceptions, MILWAUKEE will repair or replace any
part on an electric power tool which, after examination, is determined by
MILWAUKEE to be defective in material or workmanship for a period of
five (5) years** after the date of purchase unless otherwise noted. Return
of the power tool to a MILWAUKEE factory Service Center location or
MILWAUKEE Authorized Service Station, freight prepaid and insured,
is required. A copy of the proof of purchase should be included with the
return product. This warranty does not apply to damage that MILWAUKEE
determines to be from repairs made or attempted by anyone other than
MILWAUKEE authorized personnel, misuse, alterations, abuse, normal
wear and tear, lack of maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover repair
when normal use has exhausted the life of a part including, but not limited
to, chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bum-
pers, driver blades, pistons, strikers, lifters, and bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint Sprayer;
Cordless Battery Packs; Gasoline Driven Portable Power Generators; Hand
Tools; Hoist – Electric, Lever & Hand Chain; M12™ Heated Gear; Recon-
ditioned Product; and Test & Measurement Products. There are separate
and distinct warranties available for these products.
**The warranty period for Job Site Radios, M12™ Power Port, M18™ Power
Source, Jobsite Fan and Trade Titan™ Industrial Work Carts is one (1) year
from the date of purchase. The warranty period for the Drain Cleaning Cables
and AIRSNAKE™ Drain Cleaning Air Gun Accessories is two (2) years from
the date of purchase. The warranty period for the M18™ Compact Heat
Gun, 8 Gallon Dust Extractor, M18™ Framing Nailers, M18 FUEL™ 1/2"
Ext. Anvil Controlled Torque Impact Wrench w/ ONE-KEY™, and the M18
FUEL™ 1" High Torque Impact Wrench w/ ONE-KEY™ is three (3) years
from the date of purchase. The warranty period for the LED in the LED
Work Light and the LED Upgrade Bulb for the Work Light is the lifetime of
the product subject to the limitations above. If during normal use the LED
or LED Bulb fails, the part will be replaced free of charge.
Warranty Registration is not necessary to obtain the applicable warranty on
a MILWAUKEE power tool product. The manufacturing date of the product
will be used to determine the warranty period if no proof of purchase is
provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT
FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO
NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE
THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR
ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAM-
AGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES
OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE
TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT
LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR
ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PAR-
TICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS
NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED
TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS
DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the 'Service Center Search' in the Parts & Service section of
MILWAUKEE's website www.milwaukeetool.com or call 1.800.SAWDUST
(1.800.729.3878) to locate your nearest service facility for warranty and
non-warranty service on a Milwaukee electric power tool.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA & CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 years since the original
purchase date.
This warranty card covers any defect in material and workmanship on
this Product.
To make this warranty valid, present this warranty card, sealed/stamped by
the distributor or store where you purchased the product, to the Authorized
Service Center (ASC). Or, if this card has not been sealed/stamped, present
the original proof of purchase to the ASC.
Call 55 4160-3547 to find the nearest ASC, for service, parts, accessories
or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/stamped
by the distributor or store where you purchased the product, and any faulty
piece or component will be replaced without cost for you. We will cover all
freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations
a) When the product is used in a different manner from the end-user guide
or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modified or repaired by people not authorized by
TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized Service
Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Call to 55 4160-3547
IMPORTED AND COMMERCIALIZED BY
TECHTRONIC INDUSTRIES MEXICO, S.A. DE C.V.
Miguel de Cervantes Saavedra No.301 Piso 5, Torre Norte
11520 Colonia Ampliación Granada
Miguel Hidalgo, Ciudad de Mexico, Mexico
Model:
Date of Purchase:
Distributor or Store Stamp:
RÈGLES DE SÉCURITÉ GÉNÉRALES
RELATIVES AUX OUTILS ÉLECTRIQUES
AVERTISSEMENT
illustrations et spécifications fournies avec cet
outil électrique. Ne pas suivre l'ensemble des règles
et instructions peut entraîner une électrocution, un
incendie ou des blessures graves. Conserver les
règles et les instructions à des fins de référence
ultérieure. Le terme «outil électrique» figurant dans
les avertissements ci-dessous renvoie à l'outil élec-
trique à alimentation par le réseau (à cordon) ou par
batterie (sans fil).
SÉCURITÉ DU LIEU DE TRAVAIL
• Veillez à ce que l'aire de travail soit propre et bien
éclairée. Le désordre et le manque de lumière fa-
vorisent les accidents.
• Ne pas utiliser d'outils électriques dans des at-
mosphères explosives, par exemple en présence
de liquides, gaz ou poussières inflammables. Les
outils électriques produisent des étincelles risquant
d'enflammer les poussières ou vapeurs.
• S'assurer que les enfants et les curieux se trouvent
à une bonne distance au moment d'utiliser un outil
électrique. Les distractions peuvent causer une perte
de contrôle.
SÉCURITÉ ÉLECTRIQUE
• Les fiches des outils électriques doivent correspon-
dre à la prise secteur utilisée. Ne jamais modifier
la fiche, de quelque façon que ce soit. Ne jamais
utiliser d'adaptateurs de fiche avec des outils mis
à la terre. Les fiches et prises non modifiées réduisent
le risque de choc électrique.
• Éviter tout contact avec des surfaces mises à la terre
comme des tuyaux, des radiateurs, des cuisinières
et des réfrigérateurs. Le risque de choc électrique est
accru lorsque le corps est mis à la terre.
• Ne pas exposer les outils électriques à l'eau ou
l'humidité. La pénétration d'eau dans ces outils accroît
le risque de choc électrique.
• Ne pas maltraiter le cordon d'alimentation. Ne jamais
utiliser le cordon d'alimentation pour transporter
l'outil électrique et ne jamais débrancher ce dernier
en tirant sur le cordon. Garder le cordon à l'écart
de la chaleur, de l'huile, des objets tranchants
et des pièces en mouvement. Un cordon endom-
magé ou emmêlé accroît le risque de choc électrique.
• Pour les travaux à l'extérieur, utiliser un cordon spé-
cialement conçu à cet effet. Utiliser un cordon conçu
pour l'usage extérieur réduit les risques de choc électrique.
• Si l'utilisation d'un outil électrique est inévita-
ble dans un endroit humide, utiliser une source
d'alimentation munie d'un disjoncteur de fuite de
terre. L'utilisation d'un disjoncteur de fuite de terre réduit
le risque de choc électrique.
6
Lire toutes les consignes
de sécurité, consignes,
Publicidad
Tabla de contenido
