EINHELL GC-BC 30/1 I AS Manual De Instrucciones Original página 21

4. Technical data
Engine type .........................................................
........ 2-stroke engine, air-cooled, chrome cylinder
Engine power (max.) .................... 1 kW (1.35 HP)
Displacement ........................................29.7 ccm
Idle speed of engine .................. 3000 ± 400 min
Max. engine speed...............................9600 min
Max. torque
Scythe: ................................................7200 min
Trimmer: ..............................................6600 min
Ignition .................................................Electronic
Drive ........................................Centrifugal clutch
Weight (with empty tank) ............................6.8 kg
Cutting line diameter ...................................42 cm
Cutting circle diameter of blade ..................23 cm
Cutting line length ......................................... 4 m
Cutting line diameter: ................................. 2 mm
Tank capacity ..............................................0.45 l
Spark plug ................................................ L8RTC
Danger!
Sound and vibration
L sound pressure level ..................... 92.5 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 114 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Functions
Vibration emission value a
K uncertainty = 1.5 m/s
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_GC_BC_30_1_I_AS_SPK9.indb 21 Anl_GC_BC_30_1_I_AS_SPK9.indb 21
-1
-1
-1
-1
= 6.5 m/s
2
h
2
- 21 -
GB
5. Assembly
5.1.1 Fitting the steady grip
Install the steady grip as shown in Figures 3a-3c.
Do not tighten the screws until you have set the
perfect working position with the carrying strap.
The steady grip should be aligned as shown in
Figure 1. To dismantle, proceed in reverse order.
5.1.2 Fitting the long handle (Fig. 4a-4c)
Pass the handle screw (32) through the washer
(34) and into the connecting piece of the long
handle (1) (Fig. 4b). Secure the handle screw loo-
sely with the nut (33).
Now press the locking lever (A) and push the long
handle (Fig. 4a/Item 2) carefully into the connec-
ting piece for the long handle. While doing so,
ensure that the drive shafts on the inside of the
long handle slide into each other (turn the spool
head gently, if required). The lug of the locking
lever (A) must latch into the hole (B). Now tighten
the handle screw as shown in Figure 4c. After this
initial assembly, you will only have to loosen the
handle screw and activate the lever to dismantle
the long handle.
5.1.3 Fitting the blade guard hood
Important: The cutting blade guard hood must be
fi tted if you wish to work with the cutting blade.
The guard hood for the cutting blade must be ins-
talled as shown in Figures 5a – 5c.
5.1.4 Fitting/Replacing the cutting blade
The fi tting of the cutting blade is shown in Figures
6a – 6g. To dismantle, proceed in reverse order.
•
Fit the carrier plate (22) onto the spline shaft
(Fig. 6b)
•
Securely fit the cutting blade (18) on the co-
ver ring (Fig. 6c)
•
Place the pressure plate (23) over the thread
of the spline shaft (Fig. 6d).
•
Plug on the cover of the pressure plate (24)
(Fig. 6e).
•
Look for the hole in the carrier plate, line up
with the notch underneath, lock with the sup-
plied Hexagon key (29), and tighten the nut
(25) (Fig. 6f/6g). Important: Left-hand thread
01.10.2019 10:20:45 01.10.2019 10:20:45