Install The Door Control - Craftsman 139.53960SRT Manual Del Propietário

WARNING
INSTALLATION STEP 6
CAUTION

Install the Door Control

Locate door control within sight of door, at a minimum
height of 5 feet where small children cannot reach,
away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in
new home construction), it may be mounted to a
single gang box (Figure 2).
1. Strip 7/16" of insulation from one end of bell wire
and connect to the two terminal screws on back of
door control by color: white wire to 2 and white/red
wire to 1.
2. Door Control Button: Fasten securely with
6ABx1-1/2" screws.
Console Model: Pry off cover along one side with a
screwdriver blade (see Figure 1). Fasten with
6ABx1-1/4" self-tapping screws (standard
installation) or 6-32x1" machine screws (into gang
box) as follows:
• Install bottom screw, allowing 1//8" to protrude
above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not
pierce wire with a staple, creating a short or open
circuit.
4. Connect the bell wire to the terminal screws on the
motor unit panel: white to 2; white/red to 1.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
NOTE: DO NOT connect power and operate opener
at this time. The trolley will travel to the full open
position but will not return to the close position until
the sensor beam is connected and properly aligned.
Bell
Wire
Terminal
Screws
(BACK VIEW)
DOOR CONTROL BUTTON
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of
• NEVER permit children to operate or play with door
• Activate door ONLY when it can be seen clearly, is
• ALWAYS keep garage door in sight until completely
To opener terminal screws: white to 2; white/red to 1
Figure 1
REMOVE & REPLACE COVER
To Replace,
Insert Top
Tabs First
Lighted
Push Button
Top
Mounting
Hole
WHITE
Terminal
2
Screws
RED
Bottom
1
Mounting
Bell
Hole
Wire
(BACK VIEW)
PREMIUM CONTROL CONSOLE
18
WARNING
WARNING
control.
reach of children at a minimum height of 5 feet, and
away from all moving parts of door.
control push buttons or remote control transmitters.
properly adjusted, and there are no obstructions to door
travel.
closed. NEVER permit anyone to cross path of closing
garage door.
Outside Keylock Accessory Connections
6AB x 1-1/2" Screw
Door Control Button
6AB x 1-1/4" Screw
Control Console (std installation)
6-32 x 1" Screw
Control Console (pre-wired)
To Remove,
Twist
Here
2-Conductor
Opener
Bell Wire
Terminal Screws
Light
Lock
Back Panel
of Opener
HARDWARE SHOWN
ACTUAL SIZE
Insulated
Staples
Dry Wall Anchors
Figure 2
PRE-WIRED
INSTALLATION
24 Volt
2-Conductor
Bell Wire in
Gang Box
1 2 3
9 1 9 1
7 3 7 3
5 5
KG KG
Antenna