ELICA Twin Manual Del Usuario página 19

First proceed with filter maintenance as described in
corresponding paragraph.
Press and hold down (for more than 3 seconds) the T1 button
on the control panel, the LED light will stop flashing indicating
that the signal reset has been carried out, the hood will switch
off.
Reset coal filter saturation signal (FLASHING ORANGE
(amber) LED light)
First proceed with filter maintenance as described in
corresponding paragraph.
Press and hold down (for more than 3 seconds) the T1 button
on the control panel, the LED light will stop flashing indicating
that the signal reset has been carried out, the hood will switch
off.
Coal filter saturation signal disactivaction (for particular
applications)
Switch off hood (see above paragraph "suction speed (power)
selection").
Press and hold down (for more than 5 seconds) the T1 button
on the control panel, the LED light will start flashing GREEN
indicating that the coal filter saturation signal has been
disactivated.
In order to reactivate the coal filter saturation signal, repeat
operation, the LED light will flash ORANGE (amber)
Command panel disassembly.
Remove equipment from electrical grid.
Remove grease filter.
Disconnect connectors.
Extract command panel by lifting it with a small screwdriver or
similar tool.
Fig. 16
Using the remote control
The remote control is able to control all the functions of the
hood:
Select the suction speed (power)
Control the central light
Control the lateral lights
Reset e configure the saturation of the filters signal
Selecting the suction speed (power):
Press the "◄" key or the "►" key until you see the symbol
relating to the "Select the suction speed (power)" function.
Press the "+" key or the "-" key or the "■" key respectively to
increase or diminish or switch off (stand-by) the speed
(suction power).
Controlling the central light:
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Controlling the central light" function on the
remote control.
The central light can be switched on and off in two ways:
1. Press the "+" key or the "-" key respectively to switch the
central light (ON) or (OFF).
2. Press the "■" key to change the state of the light from
(OFF) to (ON) or vice versa.
Controlling the lateral lights:
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Controlling the lateral lights" function on the
remote control.
Press the "■" key to change the state of the lateral lights from
(OFF) to (ON) at maximum intensity and viceversa.
Press the "-" key to diminish the intensity of the lateral lights
until switching them off.
Press the "+" key to increase the intensity of the lateral lights.
Resetting and configuring the saturation of the filters
signal
Switch the hood on at any speed (see paragraph above
"Selecting the suction speed (power").
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Resetting and configuration of the saturation of
the filters signal" function on the remote control.
Resetting the anti-fat filter saturation signal (GREEN LED
FLASHING on the control bar)
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Press the "+" and "-" keys contemporaneously for about 3
seconds. The LED stops flashing, indicating that the resetting
of the signal has been accomplished.
Resetting the carbon filter saturation signal (ORANGE
(amber) LED FLASHING)
Note! The reset of the carbon filter saturation signal is
normally deactivated. To activate it, see under paragraph
"Activating the carbon filter saturation signal".
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Press the "+" and "-" keys contemporaneously for about 3
seconds. The LED stops flashing, indicating that the resetting
of the signal has been accomplished.
Deactivating the carbon filter saturation signal (for
special applications)
Switch the hood off (see paragraph above "Selecting the
suction speed (power)").
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Resetting and configuration of the filters
saturation signal" function on the remote control.
Press keys "+" and "-" contemporaneously for about 3
seconds. The LED flashes in GREEN to indicate that the
carbon filter saturation signal has been deactivated.
To reactivate the carbon filter saturation signal, repeat the
operation. The LED flashes in ORANGE.
17