Skil F0157347 Serie Manual Original página 8

e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
• This tool should not be used by people under the age of
16 years
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• This tool is not suitable for wet sanding
Dust from material such as paint containing lead, some
•
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
Do not work materials containing asbestos (asbestos
•
is considered carcinogenic)
• When sanding metal, sparks are generated; do not
use dust bag and keep other persons and combustible
material from work area
• Regularly clean the power tool's air vents (the
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards)
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Do not continue to use worn, torn or heavily clogged
sanding sheets
BEFORE USE
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
DURING USE
• The noise level when working can exceed 85 dB(A); wear
ear protection
• Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
• Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
• Do not touch the moving sanding sheet
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
• Mounting of sanding sheet 6
! disconnect the plug
- if necessary, clean backing pad first
! perforation in sanding sheet should correspond
with perforation in sanding foot
! the dust suction requires the use of perforated
sanding sheets
! always use the tool with the total sanding surface
covered with sanding paper
! replace worn sanding sheets in time
• On/off switch
- switch on/off the tool by pushing switch A 2 forward/
backwards
! before the sanding surface reaches the workpiece,
you should switch on the tool
! before switching off the tool, you should lift it from
the workpiece
• Dust suction 7
! empty dust bag B regularly for optimal dust pick-
up performance
- remove dust bag B by pressing knob C and hold it in
that position while pulling dust bag backwards
- mount dust bag B by sliding it back until it clicks into
place
8