Ec Declaration Of Conformity; General Power Tool Safety Warnings - DeWalt D25830 Traducido De Las Instrucciones Originales

EC-Declaration of Conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
D25830
D WALT declares that these products described
E
under "technical data" are in compliance with:
98/37/EC (until Dec. 28, 2009), 2006/42/EC (from
Dec. 29, 2009), EN 60745-1, EN 60745-2-6;
2000/14/EC, Electrical concrete breaker (hand-held),
m ≤ 15 kg, Annex VIII, TÜV Rheinland Product
Safety GmbH (0197), D-51105 Köln, Germany,
Notified Body ID No.: 0197
Level of acoustic power according to 2000/14/EC
(Article 12, Annex III, No. 10; m ≤ 15 kg):
L (measured sound power level)
WA
L (guaranteed sound power level)
WA
These products also comply with Directive
2004/108/EC. For more information, please contact
D WALT at the following address or refer to the
E
back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
D WALT.
E
Horst Grossmann
Vice President Engineering and Product
Development
D WALT, Richard-Klinger-Straße 11,
E
D-65510, Idstein, Germany
03.08.2009
WARNING: To reduce the risk of injury,
read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term "power tool" in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
dB 104
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
dB 105
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
EN GL IS H
23