Getting Started; Battery Installation; How To Operate; Setting Mode - TFA 35.1083 Instrucciones De Uso

TFA_No_35.1083_Anleit_10_17
GAIA
– Wireless weather station
26. Pressure history graph of the last 24 hours
27. Pressure display
28. Pressure display unit (inHg or hPa)
29. Pressure alarm on indicator
Buttons
B1: "SET" button
B2: "ALM" button
B3: "MAX/MIN" button
B4: "+" button
B5: "SNOOZE/LIGHT" button
Housing
C1: Wall mount hole
C2: Battery compartment
C3: Stand (fold out)
5.2. Sensor unit (Transmitter) Fig. 2
D1: Outdoor temperature and humidity
D2: Wall bracket
D3: Battery compartment

6. Getting started

6.1 Battery installation

• Take the transmitter out of its holder and open the battery
compartment of the basic unit and the transmitter (screwed) and
place both instruments on a desk with a distance of approximate-
ly 1.5 meter. Check that no other electronic devices are close.
• Insert 2 x AAA 1,5 V batteries first into the battery compartment
of the transmitter and immediately afterwards 3 x AA 1,5 V in the
basic unit, observing the correct polarity.
6.2 Reception of outdoor values and DCF time
• When the basic unit is powered up, a short beep will sound and all
LCD segments will light up for about 3 seconds before it enters into
learning mode to learn the transmitters security code.
• After the transmitter is powered up, it will transmit the tempera-
ture and humidtiy and then the transmitter will start radio-con-
trolled time reception. During the DCF time reception period (max.
10 minutes), no weather data will be transmitted.
• Note: DO NOT PRESS ANY KEY during the first 10 minutes learning
period or before radio-controlled time is displayed on the receiver.
After both outdoor values and radio-controlled time are displayed
you can place your transmitter outdoors at the final destination. In
case the clock cannot detect the DCF-signal (for example due to dis-
turbances, transmitting distance, etc.), the time can be set manual-
ly. If the outdoor weather data is not displayed or if any button is
pressed before the weather station receives the signal, or when
changing batteries you will need to follow the battery installation
procedure again.
16
11.10.2017 11:57 Uhr Seite 9
GAIA
– Wireless weather station
Please wait minimum 10 seconds before inserting the batteries
again to make a proper reset for both transmitter and receiver.
Note for radio-controlled time DCF:
• The time base for the radio-controlled time is a caesium atomic
clock operated by the Physikalisch Technische Bundesanstalt
Braunschweig. It has a time deviation of less than one second in
one million years. The time is coded and transmitted from Main-
flingen near Frankfurt via frequency signal DCF-77 (77.5 kHz) and
has a transmitting range of approximately 1,500 km. Your radio-
controlled clock receives this signal and converts it to show the
precise time. Changeover from summer time or winter time is
automatic. The quality of the reception depends mainly on the
geographic location. Normally there should be no reception prob-
lems within a 1,500 km radius around Frankfurt.
Please take note of the following:
• The recommended distance to any interfering sources like com-
puter monitors or TV sets is a minimum of 1.5 - 2 metres.
• Within ferro-concrete rooms (basements, superstructures), the
received signal is naturally weakened. In extreme cases, please
place the unit close to a window and/or point its front or back
towards the Frankfurt transmitter.
• During night-time, the atmospheric disturbances are usually less
severe and reception is possible in most cases. A single daily
reception is adequate to keep the accuracy deviation under
1 second.
• If the reception is not successful, the DCF reception symbol dis-
appears, but the DCF time reception will be repeated again. The
manually set time will be overwritten by the DCF time when the
signal is received successfully.

7. How to operate

• The basic unit has five buttons: "SET", "ALM", "MIN/MAX"
"+"and "SNOOZE/LIGHT" button.
• And there are four program modes available: Setting, Quick Dis-
play, Min/Max Function and Alarm.
• The basic unit has five sections on the LCD: Time and date, indoor
data, outdoor data, weather forecast and pressure history.

7.1 Setting Mode

• Press the "SET" button for 3 seconds while in normal mode to
enter the normal setting mode.
• In the setting mode, press "+" button or "MIN/MAX" button to
scroll the value. Holding the "+" button or "MIN/MAX" button
will increase/decrease digits in great steps.
• The program mode can be exited at any time by either pressing
the "SNOOZE/LIGHT" button, or waiting for the 10-second time-
out to take effect.
17