Instructions Generales De Securite - Skil F0159140 Serie Instrucciones

Ocultar thumbs Ver también para F0159140 Serie:

Instrucciones (96 páginas)

Contenido

página de 93

/ 93
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

! always mount backing pad when using sanding

accessories

! never use a grinding/cutting disc without the label

("blotter") which is glued onto it

Mounting of auxiliary handle F 6

Removing/mounting of safety guard G 7

! ensure that the closed side of the protective

guard always points to the operator

Before using the tool

- ensure that accessory is correctly mounted and firmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

On/off locking switch J 8 9

! be aware of the sudden impact when the tool is

switched on

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

! the accessory continues to rotate for a short time

after the tool has been switched off

Two locking switch positions (9240/9245) 9

Two hand positions (9240/9245) 0

Grinding !

- move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

Cutting @

- do not tilt the tool while cutting

- always move the tool in same direction as arrow on

tool head, in order to prevent the tool from being

pushed out of the cut in an uncontrolled manner

- do not apply pressure on the tool; let the speed of the

cutting disc do the work

- the working speed of the cutting disc depends on the

material to be cut

- do not brake cutting discs with side pressure

Holding and guiding the tool

- always hold the tool firmly with both hands, so you

will have full control of the tool at all times

- provide for a secure stance

- pay attention to the direction of rotation; always hold

the tool so, that sparks and grinding/cutting dust fly

away from the body

- keep ventilation slots L 2 clear and uncovered

APPLICATION ADVICE

Instead of flange B 2 the "CLIC" quick-clamping flange

M 2 (SKIL accessory 2610388766) can be used

- grinding/cutting discs can then be mounted without

the use of accessory keys

! when using the 'CLIC' flange with model 9140,

spanner E 2 should be used

GUARANTEE / ENVIRONMENT

Always keep tool and cord clean (especially the

ventilation slots)

! do not attempt to clean ventilation slots by

inserting pointed objects through openings

! disconnect the plug before cleaning

This SKIL product is guaranteed in accordance with

statutory/country-specific regulations; damage due to

normal wear and tear, overload or improper handling will

be excluded from the guarantee

In case of a complaint, send the tool undismantled

together with proof of purchase to your dealer or the

nearest SKIL service station (addresses as well as the

service diagram of the tool are listed on

www.skileurope.com)

Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol # will remind you of this when the need for

disposing occurs

Meuleuse

d'angle

INTRODUCTION

Cet outil sert au meulage, au tronçonnage et à

l'ébarbage de pièces en métal et en pierre sans utiliser

de l'eau; combiné avec des accessoires spécifiques, cet

outil peut également servir au brossage et au ponçage

Lisez et conservez ce manuel d'instruction 3

SPECIFICATIONS TECHNIQUES 1

SECURITE