Samsung 4 Serie Manual Del Usuario página 31

Listening through a Receiver
¦
You can listen to sound through a receiver (i.e Home Theatre) instead of the TV speaker.
1. Select Receiver and set to On.
2. Press the EXIT button to exit.
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the
OUT (OPTICAL) jack of the TV.
✎
When the receiver (i.e Home Theatre) is set to On, you can hear sound output from the TV's Optical jack. When the
TV is displaying a DTV (aerial) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
NOTE
x
You can only control Anynet
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet
x
The Anynet functions do not operate with other manufacturers' products.
+
Troubleshooting for Anynet
¦
Problem
Anynet + does not work.
I want to start Anynet .
+
I want to exit Anynet .
+
The message "Connecting to
Anynet device..." appears on the
+
screen.
The Anynet device does not play.
+
The connected device is not
displayed.
The TV programme cannot be
recorded.
The TV sound is not output
through the receiver.
devices using the TV remote control, not the buttons on the TV.
+
+
Possible Solution
• Check if the device is an Anynet
• Connect only one receiver (home theatre).
• Check if the Anynet device power cord is properly connected.
+
• Check the Anynet device's Video/Audio/HDMI Cable connections.
+
• Check whether Anynet (HDMI-CEC) is set to On in the Anynet
+
• Check whether the TV remote control is in TV mode.
• Check whether it is Anynet exclusive remote control.
+
• Anynet doesn't work in certain situations. (Searching channels, operating Media Play or Plug & Play (Initial
+
setup), etc.)
• When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
and on again.
• Check if the Anynet Function of Anynet
+
• Check if the Anynet device is properly connected to the TV and check if the Anynet
+
in the Anynet Setup menu.
+
• Press the TOOLS button to display the Anynet
• Select View TV in the Anynet
+
• Press the SOURCE button on the TV remote control and select a device other than Anynet
• Press P >/<, PRE-CH, and
when a tuner-embedded Anynet
• You cannot use the remote control when you are configuring Anynet
• Use the remote control when the Anynet
• You cannot use the play function when
• Check whether or not the device supports Anynet
• Check whether or not the HDMI Cable is properly connected.
• Check whether Anynet (HDMI-CEC) is set to On in the Anynet
+
• Search Anynet devices again.
+
• You can connect an Anynet device using the HDMI Cable only. Some HDMI cables may not support Anynet
+
functions.
• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power
failure, please repeat the device scan.
• Check whether the antenna jack on the recording device is properly connected.
• Connect the optical cable between TV and the receiver.
+ device. The Anynet + system supports Anynet
setup menu.
+
device is set on.
+
menu and select a menu you want.
+
menu.
FAV.CH to change the TV mode. (Note that the channel button operates only
device is not connected.)
+
setting or switching to view mode is complete.
+
Plug & Play (Initial setup) is in progress.
functions.
+
setup menu.
+
DIGITAL AUDIO
device.
+
+ devices only.
(HDMI-CEC) is set to On
+
devices.
+
or switching to a view mode.
+
English
+
31