Publicidad
Idiomas disponibles
Idiomas disponibles
RIVDOM eBZ ZERO
I
Unscrew union nut (P) and release front sleeve
(B).
II
Push the latch (3) against the spring force
in the direction of the tool. The clamping
sleeve (1) can now be unscrewed and clamp-
ing jaws (2) removed. Clean clamping jaws (2)
and inspect for wear. Replace clamping jaws
(2), if necessary.
III Clean the inside and outside of clamping
sleeve (1). Grease the inside of clamping
sleeve (1) lightly with graphite grease using a
brush (4).
IV Place clamping jaws (2) into clamping
sleeve (1). Reassemble in the reverse order.
UNIVERSAL FAST CHARGER
Connect the charger to a plug socket using the
cable supplied. Push the battery (F) carefully
and without force into the holder. Remove the
battery (F) in the same way. The universal fast
charger charges all batteries (F) with the voltages
12 / 16 / 20 V in 30 minutes; the batteries are 90%
charged after approx. 22 minutes. Observe the
corresponding indicators on your charger.
The cells used for the Li ion batteries (F) of the
setting tool are high quality and state-of-the-art.
The optimum charging and discharging tempera-
ture for Li ion cells is 25°C. No complete charging
or discharging capacity can be reached above and
below 25°C.
Use only the connecting cable with IEC power
connector supplied. Different national versions are
available.
Charge only the batteries from the manufacturer
belonging to the tool.
Charge only in a temperature range between 0 and
40°C.
The charger is designed for operation in the range
from 100 - 240 V, 50-60 Hz and max. 2.0 A.
BATTERY
The battery (F) has a latch (G) on the front side.
To insert or remove the battery, press the latch
downwards and push the battery (F) into the foot of
the tool or pull it out.
Use the battery (F) in the setting tool only in the
specified temperature range between -5 and 45°C.
Charge the battery (F) only in a temperature range
between 0 and 40°C.
Use only the approved charger.
Never short-circuit the battery (F).
If the battery (F) shows signs of visible damage, do
not use it any longer.
Keep the battery (F) away from moisture and
liquids.
Dispose of the battery (F) in the proper manner.
BATTERY STORAGE
Protect the battery (F) from moisture and liquids.
Store the battery (F) only in the optimum temper-
ature range between -30°C and 25°C. The battery
(F) can be stored as follows without recharging:
Storage period between -30 and +25°C – 1.5 years
Storage period between +25 and +45°C – 3 months
Storage period between +45 and +60°C – 1 month
Do not leave the battery (F) in the car, e.g. in the
summer.
A significantly shorter operating time after recharg-
ing indicates that the battery (F) is worn out and
has to be replaced.
Observe the instructions on disposal.
BATTERY DISPOSAL
Li ion: Do not throw the battery (F) into the domes-
tic waste, fire or water. Batteries (F) are collected
and recycled or disposed of in an eco-friendly
manner.
For EU countries only:
In accordance with Directive 91/157/EEC, defective
or old batteries (F) must be recycled.
Batteries (F) that can no longer be used can be
returned to the manufacturer.
DISPOSAL OF SETTING TOOL AND FAST
CHARGER
Setting tools, chargers, accessories and packag-
ings should be recycled in an eco-friendly manner.
For EU countries only:
Do not throw setting tools into the domestic waste!
In accordance with European Directive 2002/96/
EC on Waste Electrical and Electronic Equipment
and its implementation in national law, setting tools
must be collected separately and recycled in an
eco-friendly manner at the end of their useful life.
ACCESSORIES AND SETTING TOOL
CONFIGURATION
There is a wide range of accessories for the setting
tool, such as extended front sleeves, larger col-
lecting bins, contact force control, nosepieces and
special configuration kits for other fasteners, such
as sealing plugs, lockbolt pins, etc. Contact your
manufacturer directly for further information!
English | 19
Publicidad
