DeWalt DCE531 Traducido De Las Instrucciones Originales página 27

The DCB107, DCB112, DCB113 and DCB115 chargers accept
10.8V, 14.4V, 18V Li-Ion XR and XR FLEXVOLT
(DCB123, DCB127, DCB141, DCB142, DCB143, DCB144, DCB145,
DCB181, DCB182, DCB183, DCB183B, DCB184, DCB184B,
DCB185, DCB546 and DCB547) battery packs.
The DCB118 charger accepts 18V Li-Ion XR and XR FLEXVOLT
battery packs (DCB181, DCB182, DCB183, DCB183B, DCB184,
DCB184B, DCB185, DCB546 and DCB547).
Fuses:
Europe 230V tools
U.K. & Ireland 230V tools
EC-Declaration of Conformity
Machinery Directive
Concrete Vibrator
DCE531
D WALT declares that these products described under
e
Technical Data are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-12:2009.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact D
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
Markus Rompel
Director Engineering
D WALT, Richard-Klinger-Straße 11,
e
D-65510, Idstein, Germany
07.07.2016
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.

DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
battery packs
TM


TM
General Power Tool Safety Warnings

10 Amperes. mains
3 Amperes. in plugs
SAVE ALL WARNINGS AND INSTRUCTIONS
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark
b ) Do not operate power tools in explosive
WALT at
e
c ) Keep children and bystanders away while operating
WALT.
e
2) Electrical safety
a ) Power tool plugs must match the outlet. Never
b ) Avoid body contact with earthed or grounded
c ) Do not expose power tools to rain or wet conditions.
d ) Do not abuse the cord. Never use the cord for
e ) When operating a power tool outdoors, use an
f ) If operating a power tool in a damp location is
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
FOR FUTURE REFERENCE
areas invite accidents.
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
a power tool. Distractions can cause you to lose control.
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
Water entering a power tool will increase the risk of
electric shock.
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
EngLIsh
25