Electrical Connections And Adjustment Of Floats; Choice Of The Electric Control Panel; Electrical Connections - DAB FEKABOX 200 Instrucciones Para La Instalación Y El Mantenimiento

PREPARED FOR THE FOLLOWING PUMPS
FEKA VS - VX 550 MNA-TNA
FEKA VS - VX 750 MNA-TNA
FEKA VS - VX 1000 MNA-TNA
FEKA VS - VX 1200 MNA-TNA
FEKAFOS 280
FEKA FXV 20 MNA-TNA
FEKA FXC 20 MNA-TNA
DRENAG FX 15 MNA-TNA
GRINDER FX 15 MNA-TNA
6.

ELECTRICAL CONNECTIONS AND ADJUSTMENT OF FLOATS

6.1

Choice of the electric control panel

Below are the indications for the choice of a control panel only for Fekafos 280 and 280 Double and Fekafos 550 Double models because for
Fekabox models the pump is automatic.
The station must be adequately protected against overload and short-circuit.
Check the correct combination of electrical data between the control panel and the electropump. An improper combination can
cause problems and not guarantee the protection of the electric motor.
Always refer to the electropump manual and to the instructions supplied with the electric panel.
Commissioning
Always refer to the local and/or national regulations, laws and standards in force.
It is recommended to contact the Dab Assistance Service for the commissioning of the system.
For connecting the system it is recommended to use exclusively the panels ED, E-BOX indicated by the manufacturer, supplied complete with
detailed instructions for electrical connection and use.
6.2

Electrical connections

The pumps are provided with an earthed cable; ensure that the earth system is efficient. Before connecting the system to the mains, ensure
that the mains voltage is the same as the value indicated on the pump data plate and that the earth connection can be made efficiently.
It is recommended to apply the pump data plate (supplied in the package in addition to the one already applied on the pump by the
manufacturer) on the tank, in a clearly visible position, or on the control box.
The connection must be made as follows:
Pump:
Pass the pump cable through the cable gland fitted on the tank, recognisable by the symbol
cable to the panel as indicated in the respective manual.
For Dab pumps and for any pump fitted with a cable having a section of 4G1.5 mm2 or larger, to ensure that the passage and seal are
guaranteed by the cable clamps, it is advisable to replace the grommet already fitted in the clamps with the grommet supplied in the tank kit.
For references to the details, figure 10 shows an example of the replacement of the grommet on the Fekafos 280 tank.
ENGLISH
FEKAFOS 280 l
FEKAFOS 550 Double l
PREPARED FOR THE FOLLOWING PUMPS
FEKA VS - VX 550 MNA-TNA
FEKA VS - VX 750 MNA-TNA
FEKA VS - VX 1000 MNA-TNA
FEKAFOS
FEKA VS - VX 1200 MNA-TNA
550
FEKA FXV 20 MNA-TNA
DOUBLE
FEKA FXC 20 MNA-TNA
DRENAG FX 15 MNA-TNA
GRINDER FX 15 MNA-TNA
PREPARED FOR THE FOLLOWING PUMPS
FEKA VS - VX 550 MNA-TNA
FEKA VS - VX 750 MNA-TNA
FEKA VS - VX 1000 MNA-TNA
FEKAFOS
FEKA VS - VX 1200 MNA-TNA
280
FEKA FXV 20 MNA-TNA
DOUBLE
FEKA FXC 20 MNA-TNA
DRENAG FX 15 MNA-TNA
GRINDER FX 15 MNA-TNA
27
, tighten the ring nut and connect the