Maintenance / Service - Skil F0151053 Serie Manual Original

encounters excessive resistance thus reducing motor
overload and saw kickback)
- release spindle-lock button C
• Adjusting cutting depth (0-85 mm) 6
- for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
- lift lever J
- raise/lower foot K until desired cutting depth is set on
scale using indicator L
- push lever J back
• Adjusting cutting angle (0-45°) 7
- loosen knob M
- tilt tool until desired cutting angle is set on scale using
indicator N
- tighten knob M
! when bevel cutting, cutting depth does not
correspond with value on cutting depth scale
• 90° Cutting angle check 7
- adjust and tighten foot K to maximum cutting depth 6
- adjust and tighten cutting angle to 0°
- check for a 90° angle between the blade and bottom of
foot with a square
• Line-of-cut indicator P 8
- for guiding tool along desired line of cut marked on the
workpiece
- for a straight 0° cut or a 45° bevel cut use the indicator
line concerned
! the wide part of the foot should rest on the
supported part of the workpiece
! cutting width is determined by width of blade
teeth and not by width of blade body
! always make trial cuts first to verify actual line of
cut
• Dust suction
- connect vacuum cleaner to extension Q 9
! never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation
- one may also use a dust bag (SKIL accessory
2610387402)
! do not use dustbag/vacuum cleaner when cutting
metal
• Operating the tool 9
- connect plug to power source
- always hold handle R firmly with one hand and handle
S firmly with the other hand
- place tool with front end of foot flat on workpiece
! ensure that the saw teeth are not engaged into
the workpiece
- switch on tool by first pressing knob T (= safety switch
which cannot be locked) and then pulling trigger V
! the tool should run at full speed before the blade
enters into the workpiece
- lower guard F opens automatically when saw blade
enters the workpiece (open lower guard manually by
using lever G only for special cuts such as plunge
cuts)
! do not force the tool (apply light and continuous
pressure in order to avoid overheating the blade tips
and, in case of cutting plastics, melting the plastic
material)
! while working, always hold the tool at the
grey-coloured grip area(s)
- after completing the cut switch off tool by releasing
trigger V
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece
• Always face the good side of the workpiece down to
ensure minimum splintering
• Only use sharp saw blades of the correct type 0
- quality of cut improves by the number of teeth
- carbide tipped blades stay sharp up to 30 times longer
than ordinary blades
• Parallel guide W !
- for making exact cuts along a workpiece edge
- can be inserted in either side of foot
Adjusting parallel guide
- loosen knob Y
- adjust to desired cutting width by using parallel guide
scale (use line-of-cut indicator P as 0-reference)
- tighten knob Y
• Plunge cutting @
- set desired cutting depth
- tilt tool forward with line-of-cut indicator P lined up with
desired line of cut marked on the workpiece
- open lower guard F with lever G
- just before blade enters workpiece, switch on tool and
gradually lower back end of tool using front end of foot
as hinge-point
- gradually move tool downward as well as forward
- as soon as blade enters the material, release lever G
! never pull tool backwards
• Cutting large panels #
- support panel close to the cut either on floor, table or
workbench
! set cutting depth so that you cut through panel
and not through support
- in case parallel guide does not allow desired width of
cut, clamp or nail straight piece of wood to workpiece
as a guide, and use the right side of the foot against
this guide

mAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always keep tool and cord clean (especially the
ventilation slots)
! disconnect the plug before cleaning
• Always keep the area around lower guard F 5 clean
(remove dust and chips by blowing out with compressed
air or with a brush)
• Clean saw blade immediately after use (especially from
resin and glue)
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
13