Safety Instructions; Accessories; Items Supplied - Cooper Tools Weller WSD 161 Instrucciones Para El Manejo

Note: Always ensure the proper position of the soldering iron tip.
These soldering irons have been adjusted for an average-size tip. Deviations can
occur due to exchanging of the tip or using other tip designs.
If the total output of the unit is exceeded due to the connected soldering tools the
right channel will switch off automatically.
External input unit WCB 1 and WCB 2 (optional)
The following functions are possible when using an external input unit.
b Offset:
The real temperature of the soldering iron can be changed by ± 40°C
by input of a temperature offset.
b Setback:
Reduction of the setpoint temperature to 150°C (standby). The
setback time can be set at 0-99 minutes after the soldering station has
switched to standby mode. After a period equal to three times the
set-back time, the "Auto Off" function is activated. The soldering iron
is switched off (flashing dash on the display).
b Lock:
Locking the setpoint temperature. Settings cannot be changed after
the soldering station has been locked.
b °C/°F:
Switching the temperature display from °C to °F, and vice versa.
b Window:
Limitation of the temperature range to max. ± 99°C based on a locked
temperature resulting from the "LOCK" function. The locked
temperature represents the median point of the adjustable
temperature range.
b Cal:
Re-adjustment of the soldering station (WCB 2 only).

5. Safety instructions

The manufacturer assumes no liability for uses other than those described in the
operating instructions, or for unauthorized alterations.
PK Elektronik Vertriebs GmbH, Ellmendinger Str. 23, 76227 Karlsruhe
Tel.: 0721-43337, Fax: 0721-491292, vertrieb@pkelektronik.com, www.pkelektronik.com
These operating instructions and warnings should be read carefully and kept in an
easily visible location in the vicinity of the soldering iron. Non-observance of these
warnings can result in accidents, injury or risks to health.
The WELLER soldering station WSD 161 / WSL 2 is in compliance with the EC
Declaration of Conformity in accordance with the basic safety requirements specified
by Directives 89/336/EEC and 73/23/EEC.

6. Accessories

5 29 161 99 Soldering iron set WSP 80
5 33 131 99 Soldering iron set MPR 80
5 33 111 99 Soldering iron set MLR 21
5 33 112 99 Soldering iron set LR 21, antistatic
5 33 113 99 Soldering iron set LR 82
5 33 155 99 Soldering iron set WMP
5 33 133 99 Soldering iron set WTA 50
5 13 050 99 Reflow soldering unit EXIN 5
5 25 030 99 Thermal insulating unit WST 20
5 31 181 99 External input unit WCB 1
5 31 180 99 External input unit WCB 2
WPHT Stop and go iron stand (WMP)
WPH80T Stop and go iron stand (WSP 80)

7. Items Supplied

WSD 161 WSL 2
PUD 161 Control Unit PUD 161 Control Unit
2 x WSP 80 Soldering Iron 1 x WSP 80 Soldering Iron
2 x WPH Soldering 1 x WPH Soldering
Iron Holder Iron Holder
Mains Cable 1 x WMP Soldering Iron
Operating Instructions 1 x WPHM Soldering Iron Holder
Jack Plug (not USA ) Mains Cable
Operating Instructions
Jack Plug (not USA )
PUD 161
PUD 161 Control Unit
Mains Cable
Operating Instructions
Jack Plug (not USA )
26