Publicidad
Idiomas disponibles
Idiomas disponibles
835056/835096
Rated Capacity
(Safe Working Load)
1 1/2 Ton (3000 lb) (1361 kg)
Weight
18 LB (8.2 kg) - 16.6LB (7.5 kg) Jack Only
Lowered Height
5" (12.5 cm)
Maximum Height
14" (35 cm)
Capacité Nominale
(Charge de travail sure)
1 1/2 Tonnes (3000 lb) (1361 kg)
Poids
18 LB (8.2 kg) - 16.6LB (7.5 kg) Cric Rouleur Seulement
Hauteur Rétractée
5" (12.5 cm)
Hauteur Maximale
14" (35 cm)
Capacidad Calificada
(Carga de trabajo segura)
1 1/2 Toneladas (3000 lb) (1361 kg)
Peso
18 LB (8.2 kg) - 16.6LB (7.5 kg) Gato Solamente
Altura baja
5" (12.5 cm)
Altura máxima
14" (35 cm)
Lift Arm
Lifting Saddle
Bras de Lavage
Coupelle de Levage
Brazo Elevador
Asiento Elevador
Control Handle
Manche de Commande
Mango de Mando
OPERATING AND MAINTENANCE INSTRUCTION MANUAL
• STUDY, UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS BEFORE OPERATING THIS DEVICE.
• DO NOT EXCEED RATED CAPACITY
• USE ONLY ON HARD LEVEL SURFACE
• LIFTING DEVICE ONLY. IMMEDIATELY AFTER LIFTING. SUPPORT THE VEHICLE WITH APPROPRIATE MEANS
• FAILURE TO HEED THESE WARNINGS MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE
• LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE MANUFACTURER
• NO ALTERATIONS SHALL BE MADE TO THIS PRODUCT
• ONLY ATTACHMENTS AND/OR ADAPTERS SUPPLIED BY THE MANUFACTURER SHALL BE USED
• DO NOT MOVE OR DOLLY THE VEHICLE WHILE ON THE JACK.
P R N D 1 2
SPECIFICATIONS
Pump Socket
Logement de Pompe
Inspection Plate
Dado para bombear
Plaque d'Inspection
Placa de Inspección
Fill Plug
Fourche
Balanín
Used to operate release valve
Release Valve/Knob
Pour Actionner le Clapet de Décharge
Clapet de Décharge/Bouton
Utilizado para Hacer Funcionar la Válvula
Válvula de Liberación/Perilla
de Liberación
WARNING
2
OWNER AND/OR OPERATOR RESPONSIBILITY
It is the owner and/or operators responsibility to study all WARNINGS , operating, and maintenance instructions contained on the
product label and instruction manual prior to operation of this unit. The owner/operator shall retain product instructions for
future reference.
The owner and/or operator is responsible for providing maintenance, maintaining all decals or warning labels and while in use, maintaining
the unit in good working order. If the owner and/or operator is not fluent in English, French or Spanish, the product warnings and instruc-
tions shall be read and discussed with the operator in the operator's native language by the purchaser/owner or his designee. Make sure
that the operator comprehends its contents. Safety information shall be emphasized and understood prior to usage. A visual inspection
shall be made before each use of the jack by checking for abnormal conditions, such as cracked welds, leaks, and damaged or missing
parts. NOTE about Fast Lift Operation: This jack is designed to raise the lift arm to the chassis (no load) at a fast rate. This saves time and
effort when positioning the jack. This jack operates like a conventional jack when under load.
Raising vehicle:
1. Make sure the jack and vehicle are on a hard level surface.
2. Always set the vehicle parking brake and block the wheels.
3. Consult the vehicle owners manual to ascertain the location of jack points and position the jack beneath the prescribed lift point.
4. Turn the release valve/knob clockwise to the closed position. Do not over tighten!
5. To raise the vehicle to desired height, place the handle into the socket and pump up and down.
6. Place jack stands beneath the vehicle at locations recommended by the vehicle manufacturer. Do not get under the
vehicle without jack stands. Jacks are not designed to maintain heavy loads for long periods of time.
7. Turn release valve slowly counterclockwise to lower load onto jack stands.
LOWERING THE VEHICLE
Lowering vehicle:
1. Turn the release valve/knob clockwise to the closed position.
2. Pump the handle to lift vehicle off of jack stands
3. Remove the jack stands. Do not get under or let anyone else under the vehicle while lowering.
4. Turn the release valve/knob SLOWLY counterclockwise to lower the vehicle onto the ground.
Always store your jack in the fully lowered position. This will prevent critical areas from excessive corrosion.
Monthly maintenance is recommended. Lubrication is critical to jacks as they support heavy loads. Any restriction due to dirt,
rust, etc., can cause either slow movement or cause extremely rapid jerks, damaging the internal components. The following
steps are those designed to keep the jack well lubed:
1. Lubricate the ram, linkages, saddle and pump mechanism with light oil. Grease wheel bearings and axles.
2. A visual inspection shall be made before each use of the jack by checking for abnormal conditions, such as cracked welds, leaks, and
damaged or missing parts
3. The jack shall be inspected immediately if the lift is believed to have been subjected to an abnormal load or shock. It is
recommended that is inspection be made by a manufacture's or supplier's authorized repair facility.
4. Clean all surfaces and maintain all labels and warnings.
5. Check and maintain the ram oil level.
Do not use brake or transmission fluids, or regular motor oil as they can damage the seals. Always purchase and use products
labeled Hydraulic Jack Oil.
1. Turn release valve/knob counterclockwise to allow ram to fully retract. It may be necessary to apply force to the saddle
for lowering.
2. With jack in upright position remove oil fill plug. Oil should be even with bottom of hole. If not, top up. Do not overfill.
Always fill with new, clean hydraulic jack oil.
3. Replace fill plug.
4. Check jack operation.
At this time, consult Troubleshooting section for System Air Purge.
System Air Purge
1. Turn release valve/knob counterclockwise one full turn to open.
2. Pump handle eight full strokes.
3. Turn handle clockwise to close valve.
4. Pump handle until the lift arm reaches maximum height and continue to pump several times to remove trapped air in the ram.
JACK USE
JACK STORAGE
MAINTENANCE
CHECKING OIL LEVEL
TROUBLE SHOOTING
3
Publicidad
