Technical Data - Shopseries RC4151 Manual Del Usuario

1/4 IN. SHEET FINISHING SANDER

TECHNICAL DATA

Voltage:
Amps:
No load speed:
Dimension of base:
Orbital dia:
Protection class:
Machine weight:
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
1. CHANGING THE SANDING PAPER (See Fig. A)
To fit new sanding paper, lift up the clamp lever out of
clamp lever lock to loosen the paper clamp (8), then
insert approximately 3/16"(5mm) of one end of the
sanding paper under the sanding paper clamp (8) until
the paper contacts the housing wall. Lift up the clamp
lever (5) and move it to the lever lock position. Wrap
the sanding paper around the base plate as tightly as
possible and fix the end under the other sanding paper
clamp (8).
Make sure that the sanding paper is square to the base
plate. If not, remove and refit it again. The sanding
paper must be tightly fitted over the base plate and
secured by both the locking clamps (8). This will provide
a safe and efficient sanding environment.
To remove the sanding paper, lift up the clamp lever
(5) and move away from the clamp lever lock (6). The
sanding paper clamp (8) is now loose. Repeat with the
other clamp on the opposite side of your sander.
2. PAPER PUNCH (See Fig. B)
If sanding paper is unperforated, use the paper punch
(10) to create the dust extraction holes.
Position the punch over the base plate (4) with the
punch sides on the edges of the base-plate.
Press the punch into the base plate to punch holes into
the sanding paper. Then remove the punch and check all
the holes have been formed correctly.
3. USING THE DUST BOX (See Fig. C,D)
A) ATTACH THE DUST BOX (See Fig. C)
Your sander is equipped with a dust collection box.
To attach, slide the dust box onto the dust extraction
outlet piece and take care that the dust box locks in the
grooves of the outlet.
8
120 V~60 Hz
or foreign body being thrown into your face or eyes,
2 A
never attempt to use your sander without the dust box
12000 opm
properly installed.
4" X 4-5/16"
1/16"
B) EMPTYING DUST BOX (See Fig. D)
/II
For more efficient operation, empty dust box every
3.3 LBS
5-10mins. This will create better air flow and ventilation.
To empty the dust box, pull off the dust box off of the
dust extraction outlet and shake out dust.
4. ATTACHING SANDER TO VACUUM ADAPTOR (See
Fig. E)
Your sander is equipped with a ø1-1/4" (inner diameter)
vacuum adapter (11).
If the outer diameter of vacuum hose is ø 1-1/4", insert
the ø 1-1/4" adapter (11) into the back of dust extraction
outlet. Then connect the hose of a vacuum cleaner into
the dust adapter.
Note: Please pull the vacuum adapter and make sure it
is tightened securely on the dust outlet.
If the outer diameter of vacuum hose is ø1-3/8", insert
the hose directly into the back of dust outlet.
Please turn on the vacuum cleaner, and then turn on
the sander. If you stop sanding, first turn off the sander,
then turn off your vacuum cleaner.
5. OPERATING THE SWITCH (See Fig. F)
To start your sander, depress the protective cover over
the switch at the position marked"—". To stop your
sander, depress the protective cover at the position
marked "0".
6. FLUSH SANDING FACILITY (See Fig. G)
The sander can sand flush on three sides of the
baseplate making it easy to sand corners and edges of
mouldings.
7. ORBITAL SANDING
Your sander operates in small circular rotations which
allows efficient material removal. Operate your sander
in long sweeping movements across your workpiece
and even across the grain. For a finer finish, always use
a fine grain sanding paper and only move the sander
in the direction of the wood grain and never across the
grain. Do not allow your sander to remain in the same
position otherwise you will remove material and create
an uneven surface.
CAUTION:
To prevent the possibility of sanding dust
ENG