2.8 Blocked Cutting Cylinders; Adjustments Lubrication And Maintenance; Dimensions With Cab; Slopes - Dieteg LMAB653 Instrucciones Sobre Piezas Y Accesorios

2 SAFETY INSTRUCTIONS

2.8 BLOCKED CUTTING CYLINDERS

• Stop the engine and make sure all moving
parts are stationary.
• Apply brakes and disengage all drives.
• Release blockages with care. Keep all parts of
the body away from the cutting edge. Beware
of energy in the drive which can cause rotation
when the blockage is released.
• Keep other people away from the cutting units
as rotation of one cylinder can cause the
others to rotate.
2.9 ADJUSTMENTS, LUBRICATION AND
MAINTENANCE
• Stop the engine and make sure all moving
parts are stationary.
• Apply brakes and disengage all drives.
• Read all the appropriate servicing instructions.
• Use only the replacement parts supplied by
the original manufacturer.
• When adjusting the cutting cylinders take care
not to get hands and feet trapped when rotating
cylinders.
• Make sure that other people are not touching
any cutting units, as rotation of one cylinder
can cause the others to rotate.
• To reduce the fire hazard, keep the engine,
silencer and battery compartments free of
grass, leaves or excessive grease.
• Replace worn or damaged parts for safety.
• When working underneath lifted parts or
machines, make sure adequate support Is
provided.
• Do not dismantle the machine without
releasing or restraining forces which can cause
parts to move suddenly.
DANGER - Indicates an imminently hazardous
situation which, if not avoided, WILL result in death
or serious injury.
WARNING - Indicates a potentially hazardous
situation which, if not avoided, COULD result in death
or serious injury.
CAUTION - Indicates a potentially hazardous
situation which, if not avoided, MAY result in minor or
moderate injury and property damage. It may also be
used to alert against unsafe practices.
WARNING
Hydraulic Fluid escaping under
pressure can penetrate skin and do
serious damage. Immediate medical
assistance must be sought.
PARTS AND FITTING INSTRUCTIONS FOR DIETEG
CAB TO HIGHWAY 2130 AND PARKWAY 2250 PLUS
3.0

DIMENSIONS WITH CAB

Width of cut:
Transport width:
Overall height:
Overall length:
Overall weight of
machine:
* With 6 knife fixed head sport 200 units, full fuel
tank, and optional Lighting and Beacon kits
3.1 VIBRATION and NOISE LEVEL WITH CAB
The machine was tested for whole body and hand/arm
vibration levels. The operator was seated in the normal
operating postion with both hands on the steering
mechanism. The engine was running and the cutting
device was rotating with the machine stationary.
2130
Hand / Arm acceleration level
Whole body acceleration level
Noise emisions conform to the specification of Directive
EEC79/113, 84/558, 87/252, 88/181.
2250 Plus
Hand / Arm acceleration level
Whole body acceleration level
Noise emisions conform to the specification of Directive
EEC79/113, 84/558, 87/252, 88/181.
Sound Power Level:
2130:
2250 Plus:
3.2

SLOPES

DO NOT USE ON SLOPES GREATER THAN 15°
The slope 15° was calculated using static stability
measurements according to the requirements of
EN 836.
2.14 metres (84 1/4in)
1.5 metres (59in)
2130: 2.22 metres (87 in)
2250: 2.24 metres (88 in)
2.68 mtres (105 1/2in)
2250 Plus: 1602Kg (3531lbs)*
2130: 1547Kg (3410lbs)*
: 0.388 m/s
X axis : 0.0065 m/s
Y axis : 0.0070 m/s
Z axis : 0.0358 m/s
: 0.379 m/s
X axis : 0.0535 m/s
Y axis : 0.0277 m/s
Z axis : 0.0455 m/s
79.1dB(A) Lpa (Operator) with windows
closed, and heater off
80.0dB(A) Lpa (Operator) with windows
closed, and heater on.
87.0dB(A) Lpa (Operator) with windows
open, and heater off.
84.2dB(A) Lpa (Operator) with windows
closed, and heater off
84.8dB(A) Lpa (Operator) with windows
closed, and heater on.
88.0dB(A) Lpa (Operator) with windows
open, and heater off.
2
2
2
2
2
2
2
2
GB-3