Device Description; Mounting The Wall Bracket With Charging Function; Initial Startup; Operating Time In Maximum Mode Min - Kärcher VC 6 ourFamily Manual

Device description

Depending on the model selected, there are differences
in the equipment. The specific equipment is described
on the device packaging.
For the illustrations, refer to the graphics page.
Illustration A
Boost function LED indicator light
1
Battery/battery error message LED indicator light
2
Floor nozzle fault LED indicator light
3
Suction duct fault LED indicator light
4
* HEPA-Filter
5
Boost function button (increases the suction perfor-
6
mance)/HEPA filter cover
On/Off switch with locking lever
7
Handle
8
Replaceable battery
9
Battery unlocking button
10
Air inlet filter
11
Dust container cover flap
12
Dust container
13
Dust container cover flap unlocking button
14
Dust container suction fitting
15
Motor-driven electric brush with universal brush roll
16
and LED light
Suction pipe
17
Crevice nozzle
18
2-in-1 upholstery nozzle
19
Wall bracket with charging function
20
Charger
21
** Air inlet filter (2x)
22
** Filter cleaning tool
23
** Removable battery (2x)
24
* HEPA hygiene filter (EN 1822:1998)
** VC 6 Cordless Premium ourFamily
Mounting the wall bracket with
charging function
The scope of delivery includes a wall bracket with
charging function for correct storage of the vacuum
cleaner and accessories.
Note
Mount the wall bracket at a suitable point using the
screws and dowels supplied.
For safe storage of the device, the lower screw fasten-
ing of the wall bracket should be placed at a distance of
0.83-0.85 m from the floor.
Illustration F
ATTENTION
Material damage due to incorrect installation
Incorrect installation can damage both the device and
the floor covering if it falls.
Use suitable mounting tools for wall mounting.
12
Take the weight of the device and the loading capacity
of the installation location into account when selecting
the fasteners.
WARNING
Risk of electric shock and injuries
Make sure there are no electrical cables, water or gas
pipes in the wall around the mounting area.

Installing accessories

Note
The multi-function brush is also driven by its own inte-
grated motor and must therefore always be connected
directly to the hand-held device or the suction pipe in or-
der to ensure the power supply.
All other accessor parts can also be used directly with
the hand-held device or with the suction pipe to increase
the reach.
 Push the suction pipe on to the suction fitting of the
dust container until it audibly clicks into place.
 Press the unlocking button and remove the suction
pipe from the suction fitting.
Illustration B
 Push the floor nozzle on to the suction pipe until it
audibly clicks into place.
 Press the unlocking button and remove the floor
nozzle from the suction pipe.
Illustration C
 Push accessory, such as the crevice nozzle, on to
the suction fitting of the dust container or suction
pipe until it audibly clicks into place.
Illustration D
Inserting the battery
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Note
Use only fully charged batteries.
1. Push the battery into the mounting in the device until
it audibly latches into place.
Illustration E
Note
The device is not supplied with a charged battery. Fully
charge the battery before using it for the first time.
Please observe the enclosed safety instructions for bat-
tery powered vacuum cleaners.
Note
The battery can be charged with the device or separate-
ly (e.g. for variants with an additional battery).
Note
For a detailed description of the LED displays, see
chapter LED display
1. Charge the battery with the device.
 To charge the device, attach it to the wall bracket
with charging function included in the scope of
delivery.
Illustration F
2. Charge the battery separately.
 Place the battery on a flat and safe surface to
charge it.
English

Initial startup

Battery charging