Additional Safety Instructions - VONROC DS501AC Traducción Del Manual Original

EN
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can
cause severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool be-
fore making any adjustments, changing acces-
sories, or storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
4
ing into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.

ADDITIONAL SAFETY INSTRUCTIONS

• Do not use oversized sanding sheets, but follow
the manufacturer's specifications for the size of
sanding sheets. Sanding sheets which project
over the sanding pad may cause injuries as well
as block and rip the sanding sheets or cause a
kickback.
• It is not recommended to sand lead paint. Lead
paint should be removed by a specialist only.
• Do not work on materials which release hazar-
dous substances (e.g. asbestos). Take precauti-
ons if hazardous, combustible or explosive dust
is likely to occur. Wear protective dust mask.
Use dust extraction system.
• If plaster board or plaster is sanded, this may
cause static electricity to build up on the tool.
To ensure your safety, the wall sander is earthed.
Remove dust with an earthed dust extractor only.
• Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
• Do not use the machine for sanding magnesium
workpieces.
• Wear safety goggles. Wear hearing protection.
If necessary, use other protective means, such
as safety gloves, safety shoes, etc.
• Hold the machine by the insulated gripping
surfaces where the accessory may contact hid-
den wiring or the mains cable. If the accessory
contacts a ‚live' wire, the exposed metal parts
of the machine can also become ‚live'. Risk of
electric shock.
• Be very careful when sanding painted surfaces.
• Before use, remove all nails and other metal
objects from the workpiece.
• Make sure that the workpiece is properly sup-
WWW.VONROC.COM