VONROC DS501AC Traducción Del Manual Original página 6

EN
Connecting the dust extraction system (Fig. A, C)
It is highly recommended to use the machine with
the dust hose and dust bag, ensuring optimal dust
extraction.
• Push the Dust hose (13) onto the Dust extracti-
on port (6) as shown on figure C.
• Make sure the dust bag is mounted to the dust
hose. The dust bag is fitted with a carrying
strap, allowing the user to carry the dust bag
whilst using the tool.
Note: The dust bag should be emptied when the
bag is half full to maintain optimal dust extraction.
Mounting and removing sanding paper (Fig. B)
• Hold the machine on its side or upside down, as
shown on Fig. B
• Mount sanding paper (12) with the required
grain size onto the sanding pad (11). Make
sure that the perforation in the sanding paper
(12) corresponds with the perforation on the
sanding pad (11).
• To remove the sanding paper (12), simply pull
the sanding paper from the sanding pad (11).
Note: Use coarse sanding paper for sanding rough,
uneven surfaces. Use medium sanding paper for
removing the remaining scratches from the coarse
sanding paper. Use fine sanding paper for finishing
surfaces.
Replacing the sanding pad (Fig. A)
Only install the sanding pad specified by the
manufacturer onto the machine.
Removing the sanding pad:
1. Remove sanding paper (12) from the sanding
pad (11).
2. Insert the supplied hex key into the bolt on the
sanding pad (11).
3. Whilst holding the sanding pad (11) firmly, turn
the wrench anti-clockwise to loosen the hex bolt.
4. The sanding pad (11) now can be removed.
Mounting the sanding pad:
1. Mount the sanding pad (11) onto the machine.
2. Insert the bolt into the sanding pad (11) and
insert the hex key into the bolt.
3. Whilst holding the sanding pad (11) firmly, turn
the wrench clockwise to fasten the hex bolt.
6
4. OPERATION
Switching on and off (Fig. A)
• To switch on the machine, press the lock-on
button (3) and afterwards the on/off switch (1).
• To switch the machine to continuous mode, keep
the on/off switch (1) pressed and simultaneously
press the lock-on button (3).
• To switch off continuous mode, press the on/off
switch (1) again.
• To switch off the machine, release the on/off
switch (1).
Note: It is recommended to keep the motor running
for a short period of time after sanding, so that
residual dust can be collected into the bag.
Speed adjustment (Fig. A)
The required speed can be adjusted by using the
Speed adjustment wheel (4). Also during operation
the rotational speed can be adjusted.
• To increase the speed, turn the Speed adjust-
ment knob (4) clockwise.
• To decrease the speed, turn the Speed adjust-
ment knob (4) anti-clockwise.
The required speeds depends on the material
and can be determined by practical testing.
Suction power adjustment (Fig. A)
The machine is fitted with a self-extracting dust
system, allowing dust to be extracted from the
working surface into the dust bag, helping to
maintain a clean and healthy working environment.
The suction power can be adjusted by turning the
Suction power adjustment wheel (7).
• To increase the suction power, turn the Suction
power adjustment wheel (7) clockwise.
• To decrease the suction power, turn the Suction
power adjustment wheel (7) anti-clockwise.
Note: The extraction system will only function while
the tool is in operation.
Sanding close to edges (Fig. A)
The front lid (9) of the Sanding pad cover (10) can
be removed, allowing sanding close to edges.
To remove the front lid, slide the Removable front
lid (9) downwards. To mount the lid again, simply
slide the Removable front lid (9) upwards back in
position.
WWW.VONROC.COM