Operation - EINHELL TE-ID 750/1 E Manual De Instrucciones

5.2 Fitting and adjusting the depth stop
(Fig.4/Item 2)
The depth stop (2) is held in place by the additi-
onal handle (8) by clamping. The clamp can be
released and tightened by turning the handle.
* Release the clamp and fit the depth stop (2) in
the recess provided for it in the additional handle.
•
Set the depth stop (2) to the same level as
the drill bit.
•
Pull the depth stop back by the required dril-
ling depth.
•
Turn the handle on the additional handle (8)
until it is secure.
•
Now drill the hole until the depth stop (2) tou-
ches the workpiece.
5.3 Fitting the drill bit (Fig. 5)
Always pull the power plug before making adjust-
ments to the equipment.
•
This impact drill is equipped with a spindle
lock (9) and a quick-change drill chuck.
•
Press the spindle lock (9) and turn the drill
chuck (1) until it engages. Keeping the spind-
le lock (9) pressed, turn the firmly closed drill
chuck (1) so that it opens. The drill chuck
opening must be large enough to take the
drill bit.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Keeping the spindle lock (9) pressed, turn the
drill chuck (1) so that it closes. Check that the
drill bit is secure in the chuck (1).
•
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
•
When the quick-change drill chuck (1) is open
as far as it will go (maximum drill bit opening)
and secure, press the spindle lock (9) and
turn the drill chuck (1) clockwise (viewed
from the front) until you hear a grating noise.
Keeping the spindle lock (9) pressed, turn the
drill chuck (1) approx. 5 mm in the opposite
direction until you hear a clicking noise. Then
turn the drill chuck (1) clockwise again to the
desired position. This function will prevent
damage to the drill chuck.
•
Important! Do not press the spindle lock (9)
while the drill is in use.
Anl_SA_TE_ID_750_1_E_SPK8.indb 26
GB

6. Operation

6.1 ON/OFF switch (Fig.6/Item 5)
•
First fit a suitable drill bit into the tool (see
5.3).
•
Connect the mains plug to a suitable socket.
•
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
Important. It may only be locked if the drill is set to
rotate clockwise.
To switch off:
Press the ON/OFF switch (5) briefly.
6.2 Adjusting the speed (Fig.6/Item 5)
•
You can infinitely vary the speed whilst using
the tool.
•
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (5).
•
Select the correct speed: The most suitable
speed depends on the workpiece, the type of
use and the drill bit used.
•
Low pressure on the ON/OFF switch (5):
Lower speed (suitable for: small screws and
soft materials).
•
Greater pressure on the ON/OFF switch
(5): Higher speed (suitable for large/long
screws and hard materials). Tip: Start drilling
holes at low speed. Then increase the speed
in stages.
Benefits:
•
The drill bit is easier to control when starting
the hole and will not slide away.
•
You avoid drilling messy holes (for example
in tiles).
6.3 Preselecting the speed (Fig.6/Item 6)
•
The speed setting ring (6) enables you to
define the maximum speed. The ON/OFF
switch (5) can only be pressed to the defined
maximum speed setting.
•
Set the speed using the setting ring (6) on the
ON/OFF switch (5).
•
Do not attempt to make this setting whilst the
drill is in use.
- 26 -
08.04.2019 13:34:56