Functional Description - Makita DCU180 Serie Manual De Instrucciones

6. Open the carrier frame toward the front.
► Fig.10: 1. Carrier frame
7. Unfold the handles, then insert the long hexagonal
bolts into the base unit, and then tighten the nuts with
the wrench included in the package.
► Fig.11: 1. Long hexagonal bolt
8. Tighten the shoulder bolts from the rear using the
wrench included in the package.
► Fig.12: 1. Shoulder bolt
9.
Tighten the short hexagonal bolts from both sides
using the wrench included in the package to fix the
handles.
► Fig.13: 1. Short hexagonal bolt
NOTICE:
Do not tighten the short hexagonal
bolts with excessive force. Tighten them with
proper force so that the handles are stably fixed.
NOTICE:
Do not pinch the cords with the bolts.
10. Fix the cords with the clamps.
► Fig.14: 1. Clamp
11. Fold the carrier frame.
► Fig.15: 1. Carrier frame
12. Press the lock button while pulling the brake lever
to lock the brake.
► Fig.16: 1. Lock button 2. Brake lever
CAUTION:
If the rear wheels are installed,
press the brake pedal for the rear wheel to lock
the rear wheel.
13. Hook the carrier lock, and then pull down the lock
lever to lock the carrier.
► Fig.17: 1. Carrier lock 2. Lock lever
NOTICE:
Make sure that the lock lever is locked
securely.
NOTICE:
Do not pinch the cords with the lock
lever.
NOTE: If you attach the support legs instead of the
rear wheels, remove the rear wheels from the frames,
and then attach the support legs to the frames.
► Fig.18: 1. Rear wheel 2. Support leg
Assembling and installing carrier
Optional accessory
1.
Take out the carrier from the box, attach the side
rails to the base frame, and then tighten the thumb nuts
to fix the rails.
► Fig.19: 1. Thumb nut
2. Place the carrier on the base unit, and then insert
the hexagonal bolts and washers into the frames from
the top. Tighten the washers and spring washers and
butterfly nuts from the bottom to fix the carrier.
► Fig.20: 1. Long hexagonal bolt 2. Short hexagonal bolt
3. Washer 4. Spring washer 5. Butterfly nut
NOTICE:
Use the long bolts for the front, and the
short bolts for the rear.
Installing bucket
Optional accessory
Place the bucket on the base unit, insert the hexagonal
bolts into the frames, and then tighten the washers and
spring washers and butterfly nuts from the bottom to fix
the bucket.
► Fig.21: 1. Hexagonal bolt 2. Washer 3. Spring
washer 4. Butterfly nut
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION:
Always switch off the machine
before installing or removing of the battery
cartridge.
CAUTION:
Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION:
Do not use the high-temperature
battery cartridge. When the high-temperature bat-
tery cartridge is used, the machine stops automati-
cally before a short beep sound is emitted, and may
cause an injury.
Installing the battery cartridge
1.
Rotate the lock lever, and then open the cover of
the battery box.
► Fig.22: 1. Lock lever 2. Cover
2. Align the tongue on the battery cartridge with the
slot on the battery box, and then slide the cartridge until
it locks in place with a little click. If you can see the red
indicator on the upper side of the button, battery car-
tridge is not locked completely.
► Fig.23: 1. Battery cartridge
3. Insert the lock key in the place shown in the figure
as far as it will go.
► Fig.24: 1. Lock key
NOTE: If the lock key is not inserted completely, the
machine does not work.
4. Close the cover of the battery box, and then rotate
the lock lever.
► Fig.25: 1. Lock lever 2. Cover
18 ENGLISH