Explanation Of Technical Specifications; Overload Cut-Out - Elettro SYNERGIC HI-MIG 3000 Manual De Instrucciones

INSTRUCTION MANUAL FOR WIRE WELDING MACHINE
IMPORTANT
READ THIS MANUAL AND THE SAFETY RULES MANUAL
CAREFULLY BEFORE
SERVICING THE WELDING MACHINE, PAYING SPECIAL
ATTENTION TO SAFETY
DISTRIBUTOR IF YOU DO NOT FULLY UNDERSTAND
THESE INSTRUCTIONS.
This machine must be used for welding only.
It must not be used to defrost pipes.
It is also essential to pay special attention to the "SAFETY
RULES" Manual. The symbols next to certain paragraphs
indicate points requiring extra attention, practical advice or
simple information.
This MANUAL and the "SAFETY RULES" MANUAL must be
stored carefully in a pica familiar to everyone involved in using
the machine.
They must be consulted whenever doubts arise and be kept
for the entire lifespan of the machine; they will also be used for
ordering replacement parts.
1 GENERAL DESCRIPTION
1.1 SPECIFICATIONS
This manual has been prepared for the purpose of educating
personnel assigned to install, operate and service the welding
machine.
This welding machine is a power source developed with
inverter technology, suitable for MIG.
Upon receiving the machine, make sure there are no broken
or damaged parts.
The purchaser should address any complaints for losses or
damage to the vector.
Please indicate the article and serial number whenever
requesting information about the welding machine.

1.2 EXPLANATION OF TECHNICAL SPECIFICATIONS

IEC60974-1 The welding machine is manufactured
IEC60974-10 according to these international standards.
CL. A Machine for
use.
Three-phase static transformer-rectifier
frequency converter.
MIG-MAG Suitable for MIG-MAG welding.
U Secondary open-circuit voltage.
0
X Duty cycle percentage. The duty cycle
expresses the percentage of 10 minutes
during which the welding machine may run at
a certain current without overheating.
I Welding current
2
U Secondary voltage with current I
2
U Rated supply voltage
1
3 ~ 50/60Hz 50- or 60-Hz three-phase power supply.
I max Max. absorbed current at the corresponding
1
current I and voltage U
2
All manuals and user guides at all-guides.com
INSTALLING, USING, OR
RULES. CONTACT YOUR
professional and industrial
.
2
.
2
I eff This is the maximum value of the actual
1
current absorbed, considering the duty cycle.
This value usually corresponds to the capacity
of the fuse (delayed type) to be used as a
protection for the equipment.
IP23 Protection rating for the housing.
Grade 3 as the second digit means that this
equipment is suitable for use outdoors in the
rain.
Suitable for use in high-risk environments.
NOTES: The welding machine has also been designed for use
in environments with a pollution rating of 3. (See IEC 60664).
2 INSTALLATION
• Only skilled personnel should install the machine.
• All connections must be carried out according to
current regulations, and in full observance of safety
laws.
Make sure that the supply voltage corresponds to the value
indicated on the power cable. If it is not already fitted, connect
a plug suited to the power cable, making sure that the
yellow/green conductor is connected to the earth pin.
The capacity of the overload cut-out switch or fuses installed
in series with the power supply must be equivalent to the
absorbed current I1 max. of the machine.
2.1 PLACEMENT
Place the welding machine in a ventilated area.
Dust, dirt, and any other foreign matter entering the welding
machine can interfere with ventilation and thus with smooth
operation.
Therefore, in relation to the environment and working
conditions, it is important to keep the internal parts clean.
Clean using a jet of dry, clean air, being careful to avoid
damaging the machine in any way.
Before working inside the welding machine, make sure it is
unplugged from the power mains.
Any intervention carried out inside the welding machine must
be performed by qualified personnel.
2.2 PROTECTIONS
2.2.1 Block protection
In the event of a malfunction, the display screen B will show
the message WARNING to identify the type of fault.
If this message does not disappear when the machine is
switched off and back on, contact the after-sales service.

2.2.2 Overload cut-out

This appliance is protected by a thermostat that prevents
machine operation whenever acceptable temperatures are
exceeded.
In these conditions, the fan continues to operate and the
display screen B shows the message WARNING tH in flashing
mode.
3 CONTROLS ON THE FRONT PANEL (Pict. 1)
A - KNOB
Selects and adjusts both the welding functions and
parameters.
B - DISPLAY SCREEN.
This displays both the welding parameters and all the
welding functions.
C - CENTRALIZED COUPLING
To which the welding torch must be connected.
D - EARTH LEAD OR SOCKET
Where you must connect the earth cable connector.
7