Operation
Auxiliary Inputs
AV1 Front
3.5mm input on the front of the unit. Select AV1 from the Main Menu to listen to
audio from connected device.
AV2 Rear
3.5mm input on the rear of the unit. Select AV2 from the Main Menu to listen to
audio from connected device.
Rear Camera Operation (Optional)
Using the Rear Camera
When using the optional camera, the camera is activated automatically when your
vehicle is put into reversed. By touching the CAMERA icon from the main menu,
this turns the camera on/off manually.
Remote Control
MUTE button
EJECT button
SRC (Search) button
POWER button
NUMBER buttons
VOL (Volume) buttons
INFO button
SRCH (Search) button
BAND/STOP button
ESC button
SEL (Select) button
PIC (Picture) button
NAVIGATION buttons
MENU button
A--B button
OK button
REPEAT button
TITLE button
ROOT button
SKIP (Fwd/Rev) buttons
FFWD/REV buttons
ZOOM button
SUB-T (Subtitle) button
AUDIO button
ANGLE button
Load/unloading battery of remote control
1.
Please remove insulating sheet out of remote control before use. Pull out
insulating sheet in the direction as per Fig. 1.
2.
When changing battery for remote control, first pull the movable block hold in
the direction as indicated in Fig. 2, Arrow A. Then pull the battery holder out
from the remote control in the direction as indicated in Fig.2, Arrow B.
3.
Replace the old battery by a new battery with (+) polarity side upward. Then
return the battery holder to the remote control by pressing the battery holder.
Please see Fig.3.
+ Side Up
B
A
Fig. 1
Fig. 2
Fig. 3
Improper use of battery may cause overheating or
explosion. Which may result injury or fire.
Battery leakage may cause damage to the remote
control(Battery Life: 6 months with normal use in
normal room temperature).
• Do not short the battery.
• Do not throw the battery into the fire.
• To avoid the risk of accident, keep the battery out of reach of children.
illus.-11.1
illus.-11.2
14
Symptom
Diagnosis
Blown fuse
Vehicle's ignition is off
Source unit does not turn on.
Voltage applied to Red and Yellow wires is not
between 10.8 & 16 volts or there is not voltage
present
Unit is not properly grounded
Unit resets itself when engine is off
Incorrect connection between ACC and battery
No antenna or disconnected or open connection
Tuner fails to tune any stations
in cable
Unable to tune stations in seek mode
You are in a weak signal area
The USB device has been inserted with wrong
direction
USB device cannot be inserted
The USB device connector is broken
The USB device is damaged
USB device is not recognized
Connectors are loose
No sound heard with the display "No
No MP3/WMA files are not stored on the USB
File" shown
device
Sound skips or is noisy
MP3/WMA files are not connected properly
Writing error occurred. The MP3 format is not
MP3 is not playing back
compatible.
Source unit mounted at an incorrect angle
Source unit not secured properly (Standard
Disc skips excessively
Mount)
Source unit not secured properly (ISO Mount)
Disc is dirty
Sound skips or is noisy; unable to
fast forward or backward disc
Disc is heavily scratched or warped
Disc Insertion not possible
A disc is already in the disc player
Troubleshooting
Remedy
Basic
Check fuse of the unit, replace with correct rating.
If connect following the instructions, the unit will not
operate with ignition off.
Check battery, connection and fuses and repair or
replace as necessary. If voltage is above +16 volts,
have the electrical system inspected by and authorized
car service center
Check wiring and repair as necessary
Check wiring and repair as necessary
Radio
Check all connections and repair as necessary
Make sure the tuner LOC mode is off
USB Devices
Reversing the connection direction of the USB device,
try it again
Replace with a new USB device
Disconnect USB device an reconnect. If the device is
still not recognized, try replacing with a different USB
device
Store these files properly on the USB device
Use MP3/WMA files encoded properly
MP3
Make sure MP3 has been written in a supported format
Disc Player
Check mounting angle of source unit (Mount within
+ or - 20 degrees from horizontal) and repair as
necessary
Check tightness of installation sleeve and back strap;
repair or replace as necessary
Check tightness of mounting screws and repair or
replace as necessary
Clean disc with soft cloth
Replace with new disc without scratches
Press the eject button to remove disc
15