REMS Multi-Push S Instrucciones De Servicio página 28

eng
site, a
and combinations of materials was chosen. The test time has been extended in
detected. Test method B in accordance with DIN EN 806-4 is the basis for conducting
Leak testing with water can be conducted when
changing of the water can be ensured at regular intervals, after seven days
at the latest, from the time of the leak test to commissioning of the drinking
water installation. Additionally when
therefore released for connection and operation,
the system remains full from the leak test to commissioning and partial
WARNING WARNING
The hydro-pneumatic water pump installed additionally in the REMS Multi-Push
SLW for these tests is fed by the built-in compressor of the REMS Multi-Push.
The hydro-pneumatic pump generates a water pressure of max. 1.8 MPa/
18 bar/261 psi. Before conducting one of the tests with water A, B, C, it must
be assessed whether the installation to be tested will withstand the preset/
selected test pressure "p refer".
CAUTION CAUTION
Before disconnecting the high-pressure hose (26) from the pressure test with
water drain (25) or from the drinking water installation, make sure that the
pressure has been totally relieved.
The programs can be aborted at any time with the Esc button (10). Then all
the valves open and the pressure in the installation is released. The tests are
The pressure test must be repeated if necessary or the installation must be
checked and improved.
NOTICE NOTICE
The controller ends the control process to set the selected test pressure in tests
with water at a tolerance of 0 to +0.3 bar. This means that the control is ended,
for example, when setting p refer = 11 bar at a value p actual between 11.0
and 11.3 bar. This tolerance is safe because, in the pressure test with water,
the relative pressure change of pressure p refer is decisive. If ENTER is pressed,
the value p actual is taken over as p refer. So the test can also be begun at a
p refer of 11.3 bar for example.
3.4.1 Pressure test with water, test method A (EN 806-4:2010, 6.1.3.2) 3.4.1 Pressure test with water, test method A (EN 806-4:2010, 6.1.3.2)
1. Test \ Enter
2. Test with water \ Enter
3. Test with water A \ Enter
4. Check reference test pressure default (p refer) and change if necessary
6. Check test time default
7. Actual test pressure (p actual) is adjusted to reference test pressure
(p refer) \ Enter
8. Stabilisation/wait time (t stabi) running, actual test pressure (p actual) is
changed to reference test pressure (p refer) on expiring. The stabilisation/
wait time can be ended prematurely with Enter, the test time (t test) begins
immediately (\ Esc = cancel).
9. Display screen: Reference test pressure (p refer), actual test pressure
(p actual), differential test pressure (p diff), test time (t test) \ Enter
10. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.2 Pressure test with water, 3.4.2 Pressure test with water, te
compensation (EN 806-4:2010, compensation (EN 806-4:2010, 6.1.3.3)
1. Test \ Enter
2. Test with water \ Enter
3. Test with water B \ Enter
4. Test \ Enter
5. Check reference test pressure default (p refer) and change if necessary
8. Actual test pressure (p actual) is adjusted to reference test pressure (p refer)
\ Enter
9. Stabilisation/wait time (t stabi) running, actual test pressure (p actual) is
changed to reference test pressure (p refer) on expiring. The stabilisation/
wait time can be ended prematurely with Enter, test time (t test) \ Enter
(\ Esc = cancel).
10. Display screen: Reference test pressure (p refer), actual test pressure
(p actual), differential test pressure (p diff), test time (t test) \ Enter
11. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.3 Pressure test with water, ith water,
with compressed air, inert gas or water" (January 2011) of the German Central with compressed air, inert gas or water" (January 2011) of the German Central
28
Temperature Temperature
6.1.3.3)
Press connections
ls Association for Sanitary, Heating and Air Conditioning (ZVSHK), supplement Association for Sanitary, Heating and Air Conditioning (ZVSHK), supplement
to EN 806-4:2010, 6.1.3.2,) to EN 806-4:2010, 6.1.3.2,)
1. Test \ Enter
2. Test with water \ Enter
3. Test with water B \ Enter
4. Test PfS (B/2) \ Enter
5. Check reference test pressure default (p refer) and change if necessary
7. Actual test pressure (p actual) is adjusted to reference test pressure (p refer)
\ Enter, test time (t test) begins immediately (\ Esc = cancel)
8. Display screen: Reference test pressure (p refer), actual test pressure
(p actual), differential test pressure (p diff), test time (t test) \ Enter
9. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.4 Pressure test with water, 3.4.4 Pressure test with water,
water installations with compressed air, inert gas or water" (January 2011) of water installations with compressed air, inert gas or water" (January 2011) of
the German Central Association for Sanitary, Heating and Air Conditioning the German Central Association for Sanitary, Heating and Air Conditioning
(ZVSHK). (ZVSHK).
1. Test \ Enter
2. Test with water \ Enter
3. Test with water B \ Enter
4. Test \ Enter
5. Check reference test pressure default (p1 refer) and change if necessary
6. Check reference test pressure default (p2 refer) and change if necessary
9. Actual test pressure (p1 actual) is adjusted to reference test pressure
(p1 refer) \ Enter, test time (t1 test) begins immediately (\ Esc = cancel)
10. Actual test pressure (p2 actual) is adjusted to reference test pressure
(p2 refer) \ Enter, test time (t2 test) begins immediately (\ Esc = cancel)
11. Display screen: Reference test pressure (p1 refer), actual test pressure
(p1 actual), differential test pressure (p1 diff), test time (t1 test)
Reference test pressure (p2 refer), actual test pressure (p2 actual), differ-
ential test pressure (p2 diff), test time (t2 test) \ Enter
12. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.5 Pressure test with water, test method C (EN 806-4:2010, 6.1.3.4) 3.4.5 Pressure test with water, test method C (EN 806-4:2010, 6.1.3.4)
1. Test \ Enter
2. Test with water \ Enter
3. Test with water C \ Enter
4. Check reference test pressure default (p refer) and change if necessary
6. Check test time defau
7. Check test time default (t2 test) and change if necessary (11) \ Enter
8. Actual test pressure (p0 actual) is adjusted to reference test pressure
(p refer) \ Enter
9. Stabilisation/wait time (t stabi) running, actual test pressure (p actual) is
changed to reference test pressure (p refer) on expiring. The stabilisation/
wait time can be ended prematurely with Enter, the test time (t1 test) begins
immediately followed by test time (t2 test) (\ Esc = cancel).
10. Display screen: Reference test pressure (p refer), actual test pressure
(p0 actual), differential test pressure (p0 diff), test time (t0 test)
Actual test pressure (p1 actual), differential test pressure (p1 diff), test time
(t1 test) actual test pressure (p2 actual), differential test pressure (p2 diff),
test time (t2 test) \ Enter
11. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
Push SL/SLW)
WARNING WARNING
This rule of the legal German accident insurance must be observed for Germany.
on gas pipes, industrial liability insurance association rule.
In addition, for Germany, the technical rule for gas installations "Technical
Rule Worksheet G 600 April 2018 DVGW-TRGI 2018" of the DVGW German
Gas and Water Associatio
"5.6.2 Safety measures during the tests": Safety measures may need to be
taken during the tests when carrying out the load test due to the compressibility
of gases. "The max. test pressure may not exceed the value of 3 bar. Every
sudden rise in pressure in the pipe system to be tested must be avoided."
Before conducting a test with compressed air, it must be assessed whether the
installation to be tested will withstand the preset / selected test pressure "p refer".
The tests described below and the defaults stored in the REMS Multi-Push SL/
SLW correspond to the "Technical Rule Worksheet G 600 April 2018 DVGW-
eng
Plastic and metal pipe Plastic and metal pipe