Chicco AUTO-FIX Instrucciones De Uso página 27

IT COULD SERIOUSLY COMPROMISE THE
SAFETY STANDARDS.
8. Pull the belt around the child car seat as
tight as possible, ensuring that it is not slack or
twisted (diag. 18B).
9. Place the handle in the "A" position (diag. 10).
To remove the child car seat from its base unit:
Remove the diagonal belt from the guide placed
on the backrest, reposition the handle in the
"B" position (diag. 10), release the child car seat
by pulling the appropriate release handle and
simultaneously lift the seat by the carry handle.
WARNING! After fi tting the child car seat,
ALWAYS check that the car seat belt is pulled
tight and tensioned correctly. Ensure that
its buckle does not force the belt out of the
appropriate guides on the base unit, and that it
does not interfere with the guides.
WARNING: NEVER SECURE THE CAR SEAT BELT
IN ANY OTHER POSITION THAN THE ONE
SHOWN IN DIAG. 19.
Diag. 20 shows some examples of incorrect fi tting.
FITTING THE CHILD CAR SEAT
WITHOUT BASE UNIT
To fi t the child car seat without base unit in the
car, proceed as follows:
1. Lower the stop (diag. 21).
2. Place the child car seat onto the desired car seat.
3. Pull the car seat belt and fasten it to the
corresponding buckle by passing the horizontal
part through the appropriate belt guides on the
child car seat (diag. 22).
4. Take the car's diagonal seat belt and pass it
through the belt guide located at the rear of the
child car seat's backrest (diag.23).
5. Pull the belt around the child car seat as tight
as possible, ensuring that it is not slack or twisted.
WARNING: DURING TRANSPORT, THE CAR'S
DIAGONAL SEAT BELT MUST ALWAYS BE IN
THE POSITION INDICATED IN DIAG. 24. NEVER
USE THE CHILD CAR SEAT WITHOUT PASSING
THE BELT THROUGH THE APPROPRIATE GUIDE:
THIS MAY SERIOUSLY COMPROMISE YOUR
CHILD'S SAFETY.
6. Put the handle into the "A" position (diag. 10).
7. To remove the child car seat from the base
unit: repeat the above operations in reverse:
slide out the car's diagonal belt from the guide
on the backrest, reposition the handle in the
"B" position (diag. 10), unlock the child car seat
by pulling the appropriate release handle and
simultaneously lift the seat by the carry handle.
Diag. 25 shows some examples of incorrect fi tting.
Remove the diagonal belt from the guide placed
on the backrest, reposition the handle in the
All manuals and user guides at all-guides.com
27
"B" position (diag. 10), release the child car seat
by pulling the appropriate release handle and
simultaneously lift the seat by the
USING THE SUN CANOPY
The child car seat comes with a sun canopy to
protect your child from the sun and wind.
It can be easily locked and unlocked to the child
car seat by two joints, and it can be adjusted to
the desired position (diag. 26).
CHILD CAR SEAT IN THE BABY CHAIR
OR ROCKING POSITION (FOR USE AS A
RECLINED CRADLE)
When the child car seat is not used in the car, it
can also be used as a rocking or baby chair. To use
it as a rocking chair, push the stop (diag. 15) and
move the handle to position "B" (diag. 10). To use
it in a fi xed position, pull out the stop (diag. 21)
and move the handle to position "D" (diag. 10).
Important! Please
these instructions for future
reference.
WARNING: Never leave the
child unattended
WARNING: Do not use the
Reclined Cradle once your child
can sit unaided.
WARNING: This reclined cradle
is not intended for prolonged
periods of sleeping.
WARNING: It is dangerous to
use the Reclined Cradle on an
elevated surface, such as tables,
chairs, etc..
WARNING: Always use the
restraint system.
The Reclined Cradle does not
replace a cot or a bed. Should
your child need to sleep, then
it should be placed in a suitable
cot or bed.
Do not use the reclined cradle if any components
keep