CASTLE GARDEN XKH 160 HD Instrucciones De Uso página 13

All manuals and user guides at all-guides.com
5.2 Preparation
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable(s) from the spark plug(s) and re-
moving the ignition key.
5.3 Tyre pressure
Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).
5.4 Changing engine oil
This section contains tables covering the different
engines that are included in GGP's range. To facil-
itate reading, mark the data that applies to the rel-
evant machine/engine.
5.4.1 Change intervals
The table below states hours of operation and cal-
endar months. Carry out the relevant action at
whichever occurs first.
1st time
Machine
XKH 160 HD (B&S) Hours of operation/Cal-
endar months
Changing the oil
5 hours
XKH 165 HD (Honda) Hours of operation/Cal-
endar months
Changing the oil 20 hours/
1 month
Change the oil more frequently if the engine has to
operate in demanding conditions or if the ambient
temperature is high.
5.4.2 Engine Oil
Use oil according to the table below.
Oil SAE 10W-30
Service class SJ or higher
Use oil without any additives.
Do not fill with too much oil. This can cause the
engine to overheat.
Change oil when the engine is warm.
ENGLISH
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. Therefore allow the engine to
cool a few minutes before draining the
oil.
1. Attach the clamp on the oil drainage hose. Use
a polygrip or similar. See fig. 15-17:Y.
2. Move the clamp up 3-4 cm on the oil drainage
hose and pull out the plug.
3. Collect the oil in a collection vessel.
NOTE! Do not spill any oil on the drive belts.
4. Hand in the oil for disposal in accordance with
local provisions.
5. Install the oil drainage plug and move the clamp
back so that it clamps above the plug.
6. Remove the dipstick and fill with new oil.
Oil quantity:
XKH 160 HD: 1,6 l
XKH 165 HD: 0,9 l
7. After filling up the oil, start the engine and idle
for 30 seconds.
8. Check to see if there is any oil leakage.
9. Stop the engine. Wait for 30 seconds and then
check the oil level in accordance with 4.2.
5.5 Fuel filter (15, 16:Z)
Replace the fuel filter every season.
5.6 Transmission, oil (XKH 165 HD)
The oil in the hydraulic power transmission must
Then at
be checked/adjusted and changed at the intervals
intervals of
given in the table below.
50 hours/
Action
12 months
Checking – adjusting level.
Changing the oil.
100 hours/
6 months
Type of oil: Synthetic oil 5W-50.
Oil quantity when changing: approximately 3.5 li-
tres.
5.6.1 Check – adjustment
1. Place the machine on a flat surface.
2. Read off the oil level in the reservoir. See fig.
17. The level should be level with the line.
3. If necessary, top up with more oil.
5.6.2 Draining
1. Run the machine at variable speeds for 10-20
minutes to heat up the transmission oil.
2. Position the machine completely horizontally.
3. Pull out both disengagement levers according to
fig. 7:A, B.
EN
1st time Then at
intervals
of
Hours of operation
- 50
5 200
13