Information For Users - IRSAP FLAUTO 848M0718 Manual

The electronic control consists in a thermostat which allows for an ambient temperature ranging between 7°C to 30°C.
The use and operation methods are inserted in the radio control box
The thermostat can work exclusively when paired with a specially prepared electric heating element, equipped with safety devices to limit excess
temperature and make the system safe in the event of abnormal factors (see Warnings).
1 - On/Off Button
st
1 pressing: Thermostat ON (Adjustment mode). The 1
nd
2 pressing: Thermostat Standby, all the led are switched off, heating is switched off. The2nd pressure will hear a sound long-term signal
2 - Two-color led (red/green) display:
a) Red led, heating status:
- Steady: Thermostat ON and heating is switched on
- Flashing: Thermostat ON and heating in manual mode (see radio control instructions)
b) Green led, operation modes:
- Steady: Thermostat ON and heating is not switched on
- Slow flashing: Economy operation by Pilot Wire or radio control (see radio control instructions).
- Normal flashing: Holiday operation by Pilot Wire or radio control (see radio control instructions).
- Alternating green/red flashing: Thermostat sensor not working.
c) Led off: Standby operation by Pilot Wire or radio control
3 – Orange led, Radio Reception:
- Normal flashing: reception of RF command (reception of Operating mode and other settings).
- Slow flashing: thermostat to radio control pairing mode
- Fast flashing: no connection. In this case the thermostat will adjust the temperature according to the last setting received from the
radio control until a new setting is received. (Check whether the problem is caused by the batteries of the radio control or by the radio control being
too far from the thermostat, see radio control instructions.)
Paring mode (registration of the radio control code in the thermostat).
In order to pair the RF thermostat with the remote control, select Adjustment mode and then press the On/Off Button for 10 seconds until the
Orange led begins flashing slowly. The thermostat is waiting for connection with the radio control. For more information, see the radio control
instructions. Once pairing has been completed, the thermostat shifts to Adjustment mode.
When restarted after a power failure during operation, the thermostat Orange led will begin flashing fast to indicate the absence of transmission with
the radio control. Operation will be resumed automatically after a few minutes or can be instantly resumed by using the radio control to adjust the
temperature setting or Operation mode as required (see radio control instructions).
Management of the 6-function pilot wire.
In "Auto" status, and only there, the room thermostat is able to recognise the following
6 different commands sent by the Pilot Wire.
1) COMFORT: the thermostat is adjusted according to the temperature set by the user (Tset) by means of the keys (4) in Fig.A.
2) STOP: the thermostat stops the power supply to the heating resistance, irrespective of the set temperature (Tset).
3) HOLIDAY/ANTI-FREEZE FUNCTION: the thermostat is set at a temperature of 7°C.
4) ECONOMY/NIGHT REDUCED OPERATION: the thermostat is set at the temperature T = Tset - 3.5°C.
5) COMFORT OPERATION - 1°C: the thermostat is set at the temperature T = Tset - 1°C.
6) COMFORT OPERATION - 2℃: the thermostat is set at the temperature T = Tset - 2°C (red led lit)
The electric resistance switches off when the desired temperature is reached.
In each operating mode the electric resistance is controlled by an internal thermostat that limits the maximum operating temperature of the radiator.
in accordance with article 14 of the Directive 2012/19/EU of 07/07/2012 on waste electrical and electronic equipment.
• The symbol shown above, present also on the equipment, indicates that it has been placed on the market and that, when the user decides to get
rid of it, it must be disposed of in separate waste collection (including all the components, sub-assemblies and consumer materials which are an
integral part of the product).
• For information on the systems for collecting these appliances, please contact the company or another subject enrolled in the various National
Registers for other countries in the European Union. Waste produced in the home (or of similar origin) may be consigned to systems for the separate
collection of urban waste.
• When buying a new appliance of an equivalent type, it is possible to hand over the old equipment to the seller. The seller will then contact the
subject in charge of the collection of the equipment.
• The appropriate separate collection of the scrapped equipment and the subsequent operations of processing, recovery and environment-
compatible disposal, allows the avoidance of potential negative effects on the environment and on human health, while favouring the recycling and
recovery of the component materials.
The unauthorised disposal of the product by the user entails the application of the sanctions contemplated under the national approval of Directives
2011/65/EU, 2008/98/EC and 2015/1127/EU.
All manuals and user guides at all-guides.com
INSTRUCTIONS FOR USING THE ELECTRONIC THERMOSTAT
METHOD OF USE AND OPERATION
st
time the button is pressed, a double audible signal is emitted.

INFORMATION FOR USERS

(pic. A)