Publicidad
Idiomas disponibles
Idiomas disponibles
3.
Let go of the steering wheel and continue down the desired path. Once the end
of desired path is reached, release pressure on the forward drive pedal slightly to
slow down and briefly press the left or right turn button on the Operator Control
Panel (see image on previous page).
Clearing the Mowing Line
To clear points A and B and set a new mowing line:
1.
Stop the mower.
2.
Turn the PTO off.
3.
Press and hold the SET LINE/ENGAGE AUTO button on the Operator Control Panel
for a minimum of 3 seconds.
NOTE: If SET LINE/ENGAGE AUTO button is not held for a minimum of 3 seconds,
the Indicator/Warning Lights will blink yellow once to indicate an invalid reset.
4.
LINE indicator on the Operator Control Panel will turn off once points A and B
are cleared.
NOTE: Clearing the mowing line will automatically return mower to manual mode.
Holding the SET LINE/ENGAGE AUTO button for less than 3 seconds will fail to reset line
and may shift the mower back into auto mode if preset lines are still stored. Loss of
control, property damage, personal injury, or death may result.
Manual Override
To remove the mower from SurePath
Auto Steer Mode, the operator should
resume control of the steering wheel
and turn it slightly to either the right
or left. This will return the mower to
manual mode. The AUTO indicator will
be flashing.
To resume SurePath Auto Steer Mode,
briefly press the SET LINE/ENGAGE AUTO button on the Operator Control Panel.
NOTE: Do not hold the SET LINE/ENGAGE AUTO button down when resuming SurePath
Auto Steer Mode. Holding the button for 3 seconds or more will reset the system,
erasing the A and B points previously set.
Automatic Shut Off or GPM Signal Loss
If the GPM loses signal, the mower will return to manual mode. The following sequence
will occur:
1.
The Indicator/Warning Lights on the Light Module will flash red and the system
will stop steering the mower.
2.
The operator must resume control of the steering wheel and turn it slightly to
either the right or left to return to manual mode.
3.
Once GPS signal has been reacquired, the Indicator/Warning Lights will be solid
green. Briefly press the SET LINE/ENGAGE AUTO button to resume SurePath Auto
Steer Mode.
NOTE: If the SurePath Auto Steer system malfunctions see Troubleshooting section or
contact an authorized service provider.
Using the Mower Deck in SurePath Auto Steer Mode
NOTE: Operator is always in control of the mower's speed and braking.
1.
To move the mower, slowly push the forward drive pedal forward. The SurePath
Auto Steer system will keep the mower aligned with the preset mowing line.
NOTE: The speed of the mower will affect cut quality of the lawn. Mowing at full
speed will adversely affect a high quality cut lawn. Control the ground speed with
the drive pedals.
2.
When approaching the other end of the strip, release pressure on the forward
drive pedal slightly to slow down before initiating a right or left zero turn. Briefly
press the right or left turn button on the Operator Control Panel.
WARNING
Quick Reference & Troubleshooting Guide
Pro Z SurePath Auto Steer Series, Zero-Turn Commercial Mower
NOTE: Left and right turn buttons will only function if SurePath Auto Steer Mode
has been activated.
NOTE: The SurePath Auto Steer system will make smoother and more accurate
turns at lower speeds, and allow it to more easily pick up and maintain the signal
for the next parallel line to be followed.
3.
Make sure mower is realigned with mowing line before accelerating.
Troubleshooting
NOTE: SurePath Auto Steer system issues may be resolved by turning the mower off,
waiting 10 seconds and then turning the mower back on.
1.
Indicator/Warning Lights do not flash blue after key is turned on.
• Check fuses. Replace with same rating fuse. See Operator's Manual.
2.
Indicator/Warning Lights do not go solid green.
• Move away from trees and buildings. Ensure nothing is blocking the GPM.
3.
Mower is in an open area but Indicator/Warning Lights stay flashing green.
• Verify SurePath Auto Steer subscription is still active.
• Check if mower has been moved out of the state(s) where SurePath Auto Steer
subscription was activated.
NOTE: SurePath Auto Steer system functionality requires connectivity to
software and services. The first year of your subscription is included in the
price of the product. All following years will need to be renewed at the current
subscription cost. For more details, and to purchase a subscription, please
visit cubcadet.com/surepath.
• Contact an authorized service dealer if the above items are resolved.
4.
Mower is in an open area but Indicator/Warning Lights stay flashing green with
periodic red.
• Check for strength of cellular signal.
• Verify SurePath Auto Steer subscription is still active.
5.
Indicator/Warning Lights flash yellow when you press a button.
• SurePath Auto Steer system is not ready. Wait for GPS indicator to be solid green.
• Mower has not traveled minimum recommended distance to allow setting of
mowing line. See Setting the Mowing Line (SurePath Auto Steer Mode) in the
Operator's Manual.
• Invalid reset of mowing line. See Clearing the Mowing Line (SurePath Auto Steer
Mode) in the Operator's Manual.
6.
Indicator/Warning Lights flash yellow while in Auto Steer Mode.
• Mower speed too fast. Reduce speed.
7.
GPS indicator is ON but SurePath Auto Steer Mode will not engage.
• Resume use in manual mode and contact an authorized service dealer to review
active faults.
8.
Indicator/Warning Lights flash red while system is being used in SurePath Auto
Steer Mode.
• Move away from trees and buildings and verify nothing is blocking the GPM.
• Check for strength of cellular signal.
• Resume use in manual mode and contact an authorized service dealer to review
active faults.
9.
Indicator/Warning Lights flash red while in manual mode.
• Resume use in manual mode and contact an authorized service dealer to review
active faults.
10. SurePath Auto Steer Mode leaves uncut areas between mowing passes.
• Turn Cutting Width knob counter-clockwise to increase mowing overlap.
11. SurePath Auto Steer Mode is overlapping too much between mowing passes.
• Turn Cutting Width knob clockwise to reduce mowing overlap.
12. SurePath Auto Steer Mode needs to be disabled.
• Remove GPM fuse (labeled F5:GPM in the fuse box located under the operator's
seat) to disable SurePath Auto Steer system.
• Contact an authorized service dealer.
Publicidad
