Removing And Refitting The Cover - BESAFE Stretch Manual Del Usuario

16
Placing the child into the seat
1. While pressing the button of the central adjuster, pull the shoulder belts
away from the seat with a flat hand. Make sure to pull the belts evenly so
that they stay at the same length. Do not pull on the shoulder pads, as they
are fixed and cannot move. (15)
2.
Open the harness buckle.
3. To keep the straps out of the way, place the shoulder pads onto the
magnets on each side of the seat shell. (15)
4.
Place your child into the seat and adjust the position of the shoulder belts
and headrest if needed - see section "Adjusting to the growing child".
5.
Place the shoulder belts over the child's shoulders and close the buckle:
CLICK! (15)
6.
Pull the central adjuster strap straight away from the seat to tighten the
harness. Make sure to tighten the harness extremely well, so that you can
no longer make a horizontal fold in the belts. When you tighten the harness,
make sure that the child is positioned well against the backrest. (15)
Adjusting the seat to the growing child
Shoulder belt/headrest height
•
The height of the shoulder belts and the headrest can be adjusted by
pulling the headrest handle upwards at the back of the headrest and
moving the headrest up or down. To be able to do so, the harness buckle
has to be opened and the straps have to be pulled out. (16)
•
To find the right height for your child, move the headrest all the way up,
place your child into the seat, and then move the headrest downwards
until it sits directly on your child's shoulders.
•
Important for use on the front seat: you should always have a minimum
distance of 5 cm between the car's front shield and the top of the child's
head or headrest, whichever is higher. If your car does not enable this for
the highest headrest positions, you need to move the seat to the back seat
instead.
Recline angle
•
The recline angle can be adjusted to how it is comfortable for your child.
To do so, access the recline handle at the underside of the seat shell. (17)
Leg space
•
You can decide with how much leg space you want to install the seat by
adjusting the front brace position. This needs to be done before installing
the seat. See section "Preparing the child seat for installation".
Cushion inserts
•
Remove the bottom cushion when the child is over 2 years. (18)
•
Remove the back cushion when the child is over 2 years or earlier when
the child does not fit between the cushion anymore.

Removing and refitting the cover

• Do take care when you remove the cover, as re-fitting the cover is done in
reverse.
•
The cover of the headrest can be taken off separately.
•
For further instructions, please visit www.besafe.com
•
When washing the seat cover, make sure to follow the wash label on the
inside of the cover.
! Warning: potential misuse
•
The child seat MUST NOT be installed in a front passenger
seat WITH AN ACTIVATED AIRBAG.
•
The child seat MUST NOT be installed in a position where
the vehicle belt is equipped with a belt airbag that cannot be
deactivated.
•
The floor support must always be used. Make sure that the floor support
is fully pushed down and in full contact with the vehicle floor.
•
Make sure that the vehicle belt is installed tight, the lock-off is closed and
tensioned and that both lower tethers are connected with the vehicle and
tensioned tight.
Guarantee
•
Should this product prove faulty within 24 months of purchase due to
materials or manufacturing fault, except covers and harness straps,
please return it to the original place of purchase.
•
The guarantee is only valid when you use your seat appropriately and
with care. Please contact your retailer, they will decide if the seat will be
returned to the manufacturer for repair. Replacement or return cannot be
claimed. The guarantee is not extended through repair.
•
The guarantee expires: when there is no receipt, when defects are caused
by incorrect and improper use, when defects are caused by abuse,
misuse or negligence.
17