DeWalt DW130V Manual De Instrucciones página 5

Ocultar thumbs Ver también para DW130V:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3. Place key in chuck as shown in Figure 4. Using a wooden mallet or similar object, strike
key sharply in a COUNTERCLOCKWISE direction. This will loosen chuck so that it can
be unscrewed by hand.
Drilling
1. Always turn off tool and disconnect from power supply when attaching or changing bits
or accessories.
2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits,
or hole saws. For METAL, use high speed steel twist drill bits or hole saws. For
MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits
3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material,
use a "back-up" block to prevent damage to the material.
4. Always apply pressure in a straight line with the bit. Use enough pressure to keep the
drill bit biting, but do not push hard enough to stall the motor or deflect the bit.
5. Hold tool firmly to control the twisting action of the drill.
6. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT
CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL –
THIS CAN DAMAGE THE DRILL.
7. To minimize stalling on breaking through the material, reduce pressure on drill and
ease the bit through the last fractional part of the hole.
8. Keep the motor running when pulling the bit back out of a drilled hole. This will help
prevent jamming.
Drilling in Wood
Holes in wood can be made with the same twist drills used for metal. These bits may over-
heat unless pulled out frequently to clear chips from the flutes. For larger holes, use spade
bits, power auger bits, or hole saws. Work that is likely to splinter should be backed up with
a block of wood.
Drilling in Metals
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which
should be drilled dry. The cutting lubricants that work best are sulphurised cutting oil or lard
oil; bacon grease will also serve the purpose.
Drilling in Masonry
Use carbide tipped masonry bits at low speeds. Keep even force on the drill but not so
much that you crack the brittle materials. A smooth, even flow of dust indicates the proper
drilling rate.
Lubrication
All bearings used are factory lubricated to last the life of the tool. All needle bearings used
receive their lubrication from the grease in the gear case. Clean and relubricate gear case
yearly or whenever servicing requires the gear case to be removed. Use type and quanti-
ty of grease shown on Parts Bulletin packed with your tool.
Gear case is removed by removing the four screws from the front of the tool. If the chuck
is too large to permit removal of the two top screws, see instructions for chuck removal.
Motor Brushes
CAUTION: Turn off and unplug the tool before making any adjustments or remov-
ing/installing attachments or accessories.
This D
WALT tool uses an advanced brush system which automatically stops the tool
E
when the brushes wear out. This prevents serious damage to the motor.
Accessories
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center.
If you need assistance in locating any accessory, please contact D
Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-433-9258.
CAUTION: The use of any other accessory not recommended for use with this tool
could be hazardous.
For safety in use, the following accessories should be used only in sizes up to the maxi-
mums shown in the table below.
MAXIMUM RECOMMENDED CAPACITIES
Drill Capacity
RPM
Steel twist bit
Auger
Self-feed
Spade
Wood holesaw
Steel holesaw
ACCESSORY MUST BE RATED FOR USE AT SPEED EQUAL TO OR HIGHER THAN
NAMEPLATE RPM OF TOOL WITH WHICH IT IS BEING USED.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by authorized service
centers or other qualified service organizations, always using identical replacement parts.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. This warranty does not cover part failure due to nor-
mal wear or tool abuse. For further detail of warranty coverage and warranty repair infor-
mation, visit www.dewalt.com or call 1-800-4-D
does not apply to accessories or damage caused where repairs have been made or
attempted by others. This warranty gives you specific legal rights and you may have other
rights which vary in certain states or provinces.
In addition to the warranty, D
WALT tools are covered by our:
E
1 YEAR FREE SERVICE
D
WALT will maintain the tool and replace worn parts caused by normal use, for free, any
E
time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.
3
WALT Industrial Tool
E
1/2"
13mm
0-550
1/2"
13mm
1-1/2"
38mm
3"
76mm
1-1/2"
38mm
5"
127mm
4"
102mm
WALT (1-800-433-9258). This warranty
E
WALT Power Tool,
E

Publicidad

Tabla de contenido
loading

Tabla de contenido