Technical Specifications - Hudora Expert 240 Manual De Instrucciones Y De Utilización

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON
PURCHASING YOUR PRODUCT!
Please read these instructions carefully. The instructions are an integral
component of the product. Therefore, please store them and the packaging
carefully in case questions arise in the future. Please always include these
instructions when handing on the product to a third party. This product must
be assembled by an adult. This product is designed for private / domestic use
only. This product is not designed for commercial/industrial use. The use of
the product requires certain capabilities and skills. Always adjust according
to the age of the user and use for the purpose it has been designed for.

TECHNICAL SPECIFICATIONS

Item: Soccer Goal Expert 240
Item number: 76934
Dimensions when assembled: 240 x 160 x 85 cm
Purpose: Stable training goal for versatile throwing,
shooting and goalkeeper training.
If you have assembly problems or would like further information on the pro-
duct, we have all you need and more at http://www.hudora.de/.
CONTENTS
18 x Goal posts | 1 x Goal net | 1 x Screw set (16 pcs.) | 6 x Pegs (for fixation)
| 4 x Lanyard for fixing the net / tension line | 8 x Hook and loop fastener for
fixing the net | 1 x Wrench (SW4) | 1 x These instructions
Other items included are meant to facilitate safe transportation and are not
required for the installation and use of the product.
SAFETY INSTRUCTIONS
• WARNING! Not suitable for children under 36 months. Long cord. Stran-
gulation hazard.
• WARNING! Do not climb on the goal frame or net or hang from the goal
posts. There is a serious risk of injury!
• Prior to use, check all parts of the goal for damages and correct assembly.
In this regard, it is important to check the connecting elements and screw
connections for stability and fit. Any sharp edges that might have formed
must immediately be removed!
• Children should only use the product when they are under adult supervi-
sion.
• No liability is assumed for damages resulting from incorrect application of
the instruction manual.
ASSEMBLY INSTRUCTIONS
Notice: The product must be assembled by 2 adults. Lubricate the connec-
tion assemblies on the narrow ends a bit before starting the assembly. That
facilitates the assembly and extends the durability of the product!
1. Assembling the goalpost frame (fig. 1)
Mount the goal frame as shown in Fig. 1. Be sure to use the appropriately
numbered tubes. The frame tubes of the main frame 1 – 5 (posts and cross-
bar) have a diameter of 75 mm and are first inserted into each other and then
screwed. Use a screw (13) with washer (14) as shown in the figures A + B at
the top and bottom of the crossbar and at the back of each of the two posts.
The tubes of the rear goal frame (tubes with 32 mm diameter) are connected
via click connections. Make sure that the bars engage audibly.
2. Assembly of the goal net (figs. 2 and 3)
Firstly use the hook and loop fasteners (15) to attach the net to the top cor-
ners of the frame forming the back of the goal. This prevents the net from
falling down during the fitting of the net. The small pennants sewed into the
net (12) indicate the top corners of the goal and are used to position the net
on the frame. Fasten the goal net (12) to the main frame by threading the fa-
stening string (17) as shown alternately through the rear wave profile on the
main frame and the mesh of the net. Thread the fastening string (17) around
the tubes and through the mesh of the net along the bottom of the rear frame
of the goal. The ends of the fastening strings should then be knotted to the
rear wave profile and the frame tubes. The fastening strings should begin /
end at the points shown in figure 3. Then thread the last fastening string (19)
All images are examples of the design.
as shown through the upper mesh of the net and secure it to each side of the
rear frame of the goal. This acts as an additional tensioning string for the net.
3. Stand locking of the goal
Finally fix the goal frame by means of the pegs (18) on the ground. Ascertain
that the ground is suitable for the application of pegs (e.g. no water pipes for
sprinkler devices!). Make sure that the pegs are completely driven into the
ground and have firm position. Avoid protruding fastenings (risk of stumb-
ling). On too hard grounds the goal must be saved by appropriate measures
in another way against overturning in order to prevent risk of injuries (e.g.
with slabs or sandbags). Never play with an unsecured goal or never leave
the goal unsecured respectively.
USAGE INSTRUCTIONS
• Only set up the goal on level ground.
• Please keep a minimum distance of at least 3 m to any surrounding obsta-
cles.
• Secure the goal to keep it from toppling over – even if not in use.
• Avoid exposing the product unnecessarily to bad weather conditions.
Keep it in a cool and dry storage area.
• Check for any rust on the product and remove it immediately. Pushing
together the metal parts could lead to the protective layer being scratched
and rust developing.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and
after each use. Do not make any structural changes. For your own safety,
please use original spare parts only. These can be sourced from HUDORA. If
parts become damaged or if sharp edges or corners should develop, the pro-
duct may not be used any more. If in any doubt, please contact our service
team (http://www.hudora.de/). Store the product in a safe place where it is
protected from the elements, cannot be damaged, and cannot injure anyone.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collec-
tion point provided in your area. Local waste management companies will be
able to answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however,
we put just as much effort into rectifying them. You can find numerous in-
formation on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/.
7/16