Hudora BigWheel Air All Paths 280 Instrucciones De Montaje Y De Uso página 7

INSTRUCTIONS ON ASSEMBLY AND USE
EN
• The scooter is not suitable for jumps.
• Prior to using the scooter, please inform yourself about re-
stricting applicable traffic regulations for the intended area of
application.
• The use of the product requires specific skills and knowledge to
be able to avoid injuries due to crashes and collisions.
• Children should only use the product when they are under adult
supervision.
• Ensure when riding that the logo on the handlebar points to the
front or else that the push buttons is as such oriented back-
wards.
INSTRUCTIONS ON ASSEMBLY
Mount the front wheel as shown in Fig. 1 – 4. Like preassembled
make sure that the long side of the sleeve screw is inserted into the
fork from the right and the short screw is screwed against it from
the left. Also make sure that the distance rings are positioned on
both sides between rim and fork.
PLEASE PROCEED AS FOLLOWS TO GET THE SCOOTER READY
FOR USE
• Push the slide control in the folding mechanism upwards. Do
not thereby pull on the handlebars – the system should be re-
laxed. The slide control will loosen. Lift the handlebar of the
scooter upwards until the controller audibly clicks into place
(Fig. 5).
• Loosen the quick release lock on the T-bar by pushing the lever
of the quick release lock. Insert the handlebar grips into the
T-section of the handlebar stem. (Fig. 6)
• Use your thumbs to press down both locking buttons until the
grips can be easily pushed into the T-section. Turn the hand-
lebar grips until the locking buttons are positioned in the two
openings intended for them and you hear them click into place.
Check that both handlebar grips are fitted correctly by pulling
both outwards. If they do not move, they have been assembled
in accordance with the instructions. The T-bar can be locked
now (Fig. 7). If the T-bar lock does not sit firmly, open the quick
release lock again and turn the opposite screw deeper into the
thread, so that the fastening bracket fits more tightly to the
T-bar rod. Repeat this process until the T-bar rod can be aligned
securely.
• Loosen the quick release lock on the handlebar rod by pushing
the lever of the quick release lock until the lever is parallel to the
handlebar grip. (Fig. 8)
• The handlebars can be locked into place at 4 different heights.
Pull the handlebar rod out of the handlebar stem until it is at the
required height and the relevant button has snapped into place.
The maximum height cannot be exceeded due to the integrated
lock. Now close the quick release lock by pushing the lever to
the handlebar stem (Fig. 9). If the handlebar does not fit firmly
at the required height, open the quick release lock again and
turn it a few times so that the fastening bracket fits more tightly
to the handlebar rod. Repeat this process until the handlebar
rod can be aligned securely.
• Always check all parts before use to ensure they are fitting
tightly, particularly the folding mechanism, the handlebar lo-
cking and the wheels.
TO GET THE SCOOTER READY FOR TRANSPORT AGAIN,
PLEASE CARRY OUT THE FOLLOWING ACTIONS
• Loosen the quick release lock by pushing the lever of the quick
release lock away from the handlebar stem.
• Please press the locking button so that the handlebar rod can
be moved (Fig. 9). Push the handlebar rod as far as it will go into
the handlebar stem.
• Close the quick release lock by pushing the lever down to the
handlebar stem.
• Loosen the quick release lock on the T-bar by pushing the
lever of the quick release lock. Use your thumbs to press both
locking buttons in the handlebar grips and pull the handlebar
grips outwards until they are released completely from the
T-section.
• Push the handlebar grips down until they are parallel with the
handlebar shaft.
• Push the slide control in the folding mechanism upwards. The
mechanism should be loose – to release it you should rather
have a foot on the brake instead of on the footboard! (Fig.
5) Fold in the scooter by moving the handle bar towards the
footboard until it audibly clicks into place.
USAGE INSTRUCTIONS
NOTHING'S EASY AT FIRST ...
... most accidents happen to "beginners" within the first ten
minutes. Particular care should be taken during this stage.
DRIVING INSTRUCTIONS
The scooter moves when a foot is used to regularly push off, just
as with well-known children's scooters. Braking is no problem
either – simply step on the friction brake over the back wheel
(mudguard).
We recommend folding the scooter by hand after each use or
using the stand. The side stand is in the direction of movement
located on the left hand side under the deck. Its use is ensured
through simply folding and unfolding. Aluminium is a good and
light material but should also be handled carefully as it is not as
hard as steel, for example.
TIRE PRESSURE
Do not exceed the maximum tire pressure. The recommended tire
pressure for 280 mm front wheel is up to 2 bar. Do not exceed 3
bar. The recommended tire pressure for 200 mm back wheel is up
to 4,2 bar. Do not exceed 5 bar.
REMOVAL OF THE WHEEL
Use the two Allen wrenches to loosen the axle screw connections.
Pull the axle bolt from the wheel hub and remove the wheel from
the fork.
CHANGING THE BALL BEARINGS
There are two ball bearings inside the wheel hub and between
these an axle guide sleeve. A screwdriver or an Allen wrench can
be used to push the ball bearings out of the wheel hub. In order
to insert a new ball bearing, this must be pressed laterally into
the wheel hub.
7/28