HIKOKI C 8FSHE Instrucciones De Manejo página 29

(2) Adjust the bevel angle to the desired setting
while watching the bevel angle scale and indicator,
then secure the clamp lever.
WARNING
When the workpiece is secured on the left or right side
of the blade, the short cut-off portion will come to rest
on the right or left side of the saw blade. Always turn the
power off and let the saw blade stop completely before
raising the handle from the workpiece.
If the handle is raised while the saw blade is still rotating,
the cut-off piece may become jammed against the saw
blade causing fragments to scatter about dangerously.
When stopping the bevel cutting operation halfway, start
cutting after pulling back the motor head to the initial
position.
Starting from halfway, without pulling back, causes the
lower guard to be caught in the cutting groove of the
workpiece and to contact the saw blade.
14. Compound cutting procedures
Compound cutting can be performed by following the
instructions in 13 and 14 above. For maximum dimensions
for compound cutting, refer to "SPECIFICATIONS" table.
CAUTION
Always secure the workpiece with the right or left
hand and cut it by sliding the round portion of the saw
backwards with the left hand.
It is very dangerous to rotate the turntable to the left
during compound cutting because the saw blade may
come into contact with the hand that is securing the
workpiece.
In case of compound cutting (angle + bevel) by
left bevel, turn the sub-fence (optional accessory)
counterclockwise, and engage in the cutting operation.
15. Cutting long materials
When cutting long materials, use an auxiliary platform
which is the same height as the holder and base of the
special auxiliary equipment.
Capacity: wooden material (W × H × L)
300 mm × 45 mm × 1050 mm, or
180 mm × 25 mm × 1600 mm
16. Confi rmation for use Crown molding vise, Crown
molding Stopper (L) and (R) (Optional accessory)
(1) Crown molding Stopper
accessories) allow easier cuts of crown molding without
tilting the saw blade. lnstall them in the base both-sides
side to be shown in Fig. 27. After inserting tighten the
6 mm knob bolts to secure the Crown molding Stoppers.
(2) The crown molding vise (B) (Optional accessory) can be
mounted on either the left fence (Fence (B)) or the right
fence (Fence (A)). lt can unite with the slope of the crown
molding and vice can be pressed down.
Then turn the upper knob, as necessary, to securely
attach the crown molding in position. To raise or lower
the vise assembly, fi rst loosen the 6 mm knob bolt.
After adjusting the height, fi rmly tighten the 6 mm wing
bolt; then turn the upper knob, as necessary, to securely
attach the the crown molding in position (Fig. 28).
Position crown molding with its WALL CONTACT EDGE
against the guide fence and its CEILING CONTACT
EDGE against the Crown molding Stoppers as shown in
Fig. 28. Adjust the Crown molding Stoppers according
to the size of the crown molding.
Tighten the 6 mm wing bolt to secure the Crown molding
Stoppers.
WARNING
Always fi rmly clamp or vise to secure the crown molding
to the fence; otherwise the crown molding might be
thrust from the table and cause bodily harm.
Do not bevel cutting. The main body or saw blade may
contact the sub fence, resulting in an injury.
(L) and (R) (optional
CAUTION
Always confi rm that the motor head does not contact the
crown molding vise ass'y when it is lowered for cutting.
If there is any danger that it may do so, loosen the 6 mm
knob bolt and move the crown molding vise ass'y to a
position where it will not contact the saw blade.
17. Groove cutting procedures
Grooves in the workpiece can be cut by adjusting the
6 mm depth adjustment bolt (Fig. 29).
(1) Lower the motor head, and turn the 6 mm depth
adjustment bolt by hand. (Where the head of the 6 mm
depth adjustment bolt contacts the hinge.)
(2) Adjust to the desired cutting depth by setting the
distance between the saw blade and the surface of the
base. (Fig. 29)
NOTE
When cutting a single groove at either end of the
workpiece, remove the unneeded portion with a chisel.
18. Using the Light (Only Model C8FSHE)
WARNING
○ Check to ascertain that the main unit and light are off
before plugging the cord into the power socket.
○ The light lens reaches high temperatures during and
immediately after use and should not be touched under
any circumstances.
Failure to observe this may result in burns.
CAUTION
○ Do not subject the light to strong impact.
Failure to observe this may result in damage to the light
or a reduced life span.
○ Only switch the light on when cutting.
○ Do not shine the light continuously into the eyes.
Failure to observe this may result in damage to the eyes.
○ Wipe all dirt that adheres to the light lens with a soft cloth
gently so that the light is not scratched or damaged.
Scratches on the light lens may result in less luminance.
○ The light switch is fi tted with an anti-dust cover. Make
sure that the switch cover is not scratched or otherwise
damaged.
○ There are cases in which shavings may enter the switch
and prevent the light from functioning.
(1) Insert the plug on the main unit into a power socket.
(2) Set the light switch into the upper position (ON) to light
it, and into the lower position (OFF) to switch it off . (See
Fig. 30)
(3) Move the light fi tting to the right and left to adjust the
lighting position.
19. Using the dust bag (Standard accessory) (Fig. 31)
(1) Connect the dust bag with the duct of power tool.
(2) When the dust bag has become full of sawdust, dust will
be blown out of the dust bag when the saw blade rotates.
Check the dust bag periodically and empty it before it
becomes full.
(3) During bevel and compound cutting, attach the dust bag
at the right angle to the base surface.
20. Connecting the dust extractor (Sold separately)
(Fig. 32)
Do not inhale the harmful dusts generated in cutting
operation.
The dust can endanger the health of yourself and
bystanders.
Use of dust extractor can reduce dust related hazards.
By connecting with dust extractor through adapter,
joint and dust collection adapter, most of dust can be
collected.
Connect the dust extractor with adapter.
(1) Connect in order of hose (id 38 mm × 3 m long) and
adapter (Dust extractor's Standard accessory) joint
(Optional accessory) and dust collection adapter
(Optional accessory) with the duct of power tool.
29
English