Craftsman CMCCSP20 Manual De Instrucciones página 15

Regular maintenance ensures a long effective life for the tool.
After every 10 minutes of use be sure to remove the battery
(be aware the chain and bar can be hot!) check the bar and
chain for correct tension and lubricate per Adjusting Chain
Tension and Chain Oiling.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call 1‑888‑331‑4569 .
Versatrack™ (Fig. U)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.

WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hang hook.

WARNING: Ensure that the tool weight does not
exceed the maximum rated weight of 20 lb (9 kg) for
the selected Versatrack™ hook.

WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to not
exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
1. Turn the tool off, remove the battery pack
and accessories.

CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the Versatrack™ Trackwall.
2. Flip or pull open the integral hang hook
when locked into position.
3. Mount the integral hang hook to the
Versatrack™ Trackwall.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1‑888‑331‑4569.
Saw Chain and Guide Bar
After every few hours of use, remove the sprocket cover,
guide bar and chain and clean thoroughly using a soft bristle
brush. Ensure oiling hole on bar is clear of debris. When
replacing dull chains with sharp chains it is good practice to
flip the chain bar from bottom to top.
Saw Chain Sharpness

CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can
cut you when it is not running.
iMPORTAnT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
sharpening services are available from your nearest D
service center.
nOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should
be used. It is recommended that a saw chain be sharpened
no more than four times.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a CRAFTSMAN factory service center
or a CRAFTSMAN authorized service center. Always use
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
• Register online at www.craftsman.com/registration
English
26 . It clicks
WALT
e
13