Wall Mounting - Craftsman CMCCSP20 Manual De Instrucciones

English
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™

WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
10
Installing and Removing Saw Chain
(Fig. A, E–H)

WARNING: Sharp moving blade. To prevent
accidental operation, insure that battery is
disconnected from the handle before performing the
following operations. Failure to do this could result in
serious personal injury.

CAUTION: Sharp moving blade. Always wear
protective gloves when installing or removing the
chain. The chain is sharp and can cut you when it is
not running.
1. Place the pole saw on a firm surface. Rotate the two
hex head screws 12 counterclockwise with the hex
wrench 16 provided.
2. Remove sprocket cover 11
head screws.
3. To remove the saw chain
front of the housing using the flat screwdriver end of the
wrench. Turning the screw counterclockwise allows the
guide bar 13 to recede and reduces the tension on the
chain so that it may be removed.
4. Lift the worn saw chain out of the groove in the
guide bar.
5. Flip guide bar over.
6. To replace the saw chain, check to make sure that the slot
in the guide bar is over the location pins
Figure G and that hole below the slot is located over the
adjustment pin.
7. Place new chain in groove of guide bar and around
sprocket. Make sure saw teeth are facing correct direction
by matching the graphic on housing or guide bar.
8. Rotate the screw in the front of the housing clockwise to
increase the chain tension.
9. Replace sprocket cover, bar clamp, and hex head screws.
10. Follow the instructions in the section Adjusting
Chain Tension.
Adjusting Chain Tension (Fig. A, E, F, H, I)
1. With the pole saw still on a firm surface check the saw
chain 14 tension. The tension is correct when the saw
chain snaps back after being pulled 1/8" (3 mm) away
from the guide bar 13 with light force from the middle
finger and thumb as shown in Figure H. There should be
no "sag" between the guide bar and the saw chain on the
underside as shown in Figure I.
2. To adjust saw chain tension, loosen hex head
screws 12 .
3. Rotate the screw 19 in the front of the housing using
the flat screwdriver end of the wrench.
4. Do not over‑tension the saw chain as this will lead to
excessive wear and will reduce the life of the guide bar
and saw chain. Overtensioning also reduces the amount
of cuts you will get per battery charge.
5. Once saw chain tension is correct, tighten hex head
screws 12 to clamp bar.
, bar clamp 10 , and hex
14 , rotate the screw 19 in the
20 shown in