Wacker DS720 Manual De Operación página 97

Use Of Threadlockers and Sealants
Threadlocking adhesives and sealants are specified throughout this manual and should be used where indicated.
Threadlocking compounds normally break down at temperatures above 350° F (175° C). If a screw or bolt is hard to
remove, heat it using a small propane torch to break down sealant. When applying sealants, follow instructions on
container. The sealants listed below are recommended for use on WACKER equipment.
TYPE
( ) = Europe COLOR
Loctite 222 Purple
Hernon 420
Omnifit 1150 (50M)
Loctite 243 Blue
Hernon 423
Omnifit 1350 (100M)
Loctite 271 / 277 Red
Hernon 427
Omnifit 1550 (220M)
Loctite 290 Green
Hernon 431
Omnifit 1710 (230LL)
Loctite 609 Green
Hernon 822
Omnifit 1730 (230L)
Loctite 545 Brown
Hernon 947
Omnifit 1150 (50M)
Loctite 592 White
Hernon 920
Omnifit 790
Loctite 515 Purple
Hernon 910
Omnifit 10
Loctite 496 Clear
Hernon 110
Omnifit Sicomet 7000
Loctite Primer T Aerosol
Hernon Primer 10 Spray
Omnifit VC Activator
All manuals and user guides at all-guides.com
USAGE
Low strength, for locking threads smaller than 1/4" (6 mm).
Hand tool removable.
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Medium strength, for locking threads larger than 1/4" (6 mm).
Hand tool removable.
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
High strength, for all threads up to 1" (25 mm).
Heat parts before disassembly.
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Medium to high strength, for locking preassembled threads
and for sealing weld porosity (wicking).
Gaps up to 0.005" (0.13 mm)
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Medium strength retaining compound for slip or press fit
of shafts, bearings, gears, pulleys, etc.
Gaps up to 0.005" (0.13 mm)
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Hydraulic sealant
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Pipe sealant with Teflon for moderate pressures.
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Form-in-place gasket for flexible joints.
Fills gaps up to 0.05" (1.3 mm)
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Instant adhesive for bonding rubber, metal and plastics;
general purpose.
For gaps up to 0.006" (0.15 mm)
Read caution instructions before using.
Temp. range, -65 to 180 degrees F (-54 to 82 degrees C)
Fast curing primer for threadlocking, retaining and
sealing compounds. Must be used with stainless steel
hardware. Recommended for use with gasket sealants.
SEALANTS
PART NO. - SIZE
73287 - 10 ml
29311 - .5 ml
17380 - 50 ml
29312 - .5 ml
26685 - 10 ml
73285 - 50 ml
28824 - .5 ml
25316 - 10 ml
29314 - .5 ml
79356 - 50 ml
26695 - 6 ml
73289 - 50 ml
70735 - 50 ml
52676 - 1 oz.
2006124 - 6 oz.